2. 您的位置
3. 首页
4. 会议论文
5. The Design and Optimization of Annular Delivery Device on Bimetallic Tube by Twin-Roll Cast-Rolling

The Design and Optimization of Annular Delivery Device on Bimetallic Tube by Twin-Roll Cast-Rolling

来源 :第二届中国国际复合材料科技大会 (CCCM-2) | 被引量 : 0次 | 上传用户：jywang001

【摘 要】

：

　　The bimetallic composite pipe has many advantages, so that it was widely used in different area such as petrochemical, electric power industry etc.In order

【作 者】

：

HUANGHua-gui;JICe;DONGYi-kang;DUFeng-shan; 

【机 构】

：

National Engineering Research Center for Equipment and Technology of Cold Strip Rolling,Yanshan Univ

【出 处】

：

第二届中国国际复合材料科技大会 (CCCM-2)

【发表日期】

：

2015年期

下载到本地 , 更方便阅读

下载此文 赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

　　The bimetallic composite pipe has many advantages, so that it was widely used in different area such as petrochemical, electric power industry etc.In order to fabricate the bimetallic composite pipe with higher performance and efficiency, a new short flow process was present based on the twin-roll casting in this paper.

其他文献

Fabrication and properities of Nano-TiCx/Cu-Cr-Zr alloy composites

　　Nano-TiCx-Cu master alloy was prepared by the in situ method of combustion synthesis and hot press consolidation in Cu-Ti-CNTs system.The Nano-TiCx/Cu-Cr-Zr

会议

Effects of different surface-modified SiCP on the microstructures and tensile properties of SiCP/201

　　The pre-oxidized SiO2 layer and salt-bath plated Ti5Si3 coating layer were developed on the surface of SiCP.Effects of surface states of SiCP on the microst

会议

Densification mechanisms of C/Cu composites manufactured by Spark Plasma Sintering

　　Spark Plasma Sintering (SPS), a novel power consolidation technique, offers accelerated densification and limited grain growth compared to the traditional s

会议

Influence of adding Ti powder in perform on microstructure and mechanical properties of Al2O3p/steel

　　To improve the mechanical properties of alumina particle reinforced steel matrix composite, Ti powder was added into alumina preforms, a 5140 steel matrix c

会议

Properties of abrasive wear under high temperature ZTA particle reinforced steel composites

　　Cast-infiltration was used for preparing ZTA (ZrO2 toughened Al2O3) particles reinforced steel composites with the particle size range of 0.5~1, 1~2, and 2~

会议

Effects of different carbon sources on the compressive proprieties of in situ high-volume-fraction T

　　Effects of carbon sources, i.e., carbon nanotubes (CNTs), graphite, carbon black (C-black), on synthesized TiCx size, morphology and compressive properties

会议

The mechanical properties of glass cenosphere/Al syntactiv foam

　　The glass cenosphere/Al syntactic foam was prepared by pressure infiltration technique.Quasi-static compression, uniaxial tension, and three-point bending e

会议

A comparative study on the superplastic tensile behaviors of the as-extruded Ti6Al4V alloys and TiBw

　　In this study, the mechanisms behind the superplastic behavior of the as-extruded Ti6Al4V alloys and TiBw/Ti6Al4V composites with tailored architecture were

会议

Electrochemical Noise Study of Corrosion Process of Clad Metal Sheets 4343/4A60/08Al

　　Aluminum/steel clad metal sheets contain many features of easy electric conduction, easy heat conduction, corrosion resistance and metallic luster from alum

会议

Plastic Deformation Densification and Metallurgical Defect Elimination Research Status and Developme

　　Spray deposited SiC/Al matrix composite has an extensive application prospect for its excellent performances, but its application is limited by its residul

会议