【摘 要】
：
This paper investigated thermal behavior of three kinds of FC packages connected with AuSn,SAC305,and electrical conductive adhesive using 1-D thermal resistance circuit method,and finite element meth
【机 构】
：
School of Material Science and Engineering,Harbin University of Science and Technology Harbin,China;
论文部分内容阅读
This paper investigated thermal behavior of three kinds of FC packages connected with AuSn,SAC305,and electrical conductive adhesive using 1-D thermal resistance circuit method,and finite element method as well as experimental measurements.Simulation results indicated that the low thermal conductivity of electrical conductive adhesive led to high thermal resistance at this layer and decreased the thermal dissipation of the package as a bottleneck when the heat power was 0.74W in this study.The junction temperature and Rjc of adhesive package was much higher than the other two and led to package failure.SAC soldering package showed similar heat dissipation ability with the AuSn one.Additionally,the results of FE analysis show better agreement with experimental observation compared with 1-D thermal resistance circuit method.
其他文献
河北钢铁集团承德分公司360㎡2＃、3#烧结机余热发电项目自投产以来一直存在烟温不足的情况,环冷机一段烟温260-310℃,二段烟温150-220℃,三段烟温120-180℃,远远低于一段烟温400℃,二段烟温300℃,三段烟温200℃的设计值,余热锅炉所产生的蒸汽温度不能满足汽轮机最低350℃和192℃的设计要求,机组如何实现安全稳定运行是所面临主要问题.在确保机组安全稳定运行情况下,通过降参数
由于烧结生产的特殊性,生石灰、白云石及除尘灰等小颗粒干物料用量较大,在皮带机倒运过程中,导致一次混合机区域产生大量粉尘,粉尘排放浓度严重超标,操作环境极差,通过对原工艺布局进行优化改造并对混合机进料端进行整改后,区域扬尘现象得到有效遏制,同时有效降低了区域设备故障率.
对2号高炉优化操作的生产实践进行了总结.在原燃料质量劣化的条件下,通过加强入炉料管理,优化高炉操作制度,做好炉型维护及抓好炉外出渣铁工作等,使高炉冶炼水平不断提高,取得了较好的技术经济指标.
As the defects in the LED chip is an important factor affecting the properties of high-power LEDs,a new measurement system is proposed which can get nonradiative recombination defect densities of a LE
Temporal modulations of light from AC-LED sources can produce a number of visible artifacts,such as flicker,stroboscopic effect,etc.Flicker is common in low frequency situations,while the stroboscopic
Voltage-temperature coefficient (S) is the key parameter for measuring the light-emitting diode (LED)’s junction temperature.Common method for determining junction temperature by the S is under low cu
One of the most critical reliability problems that the LED COBs are facing is the failure of wire bonding connections.The LED COBs would easily break down due to the mechanical shocks or material stre
Single LED package based on encapsulated leadframe provides a common electrical and thermal path with dramatic reduction of its thermal resistance.The specific LED packaging technology consists of a s
LED display is applied in advertising,transportation,information release,etc.Traditional LED display module includes LED board,driving PCB,plastic mask and back shell.The dot pitch of traditional LED
High efficiency white light-emitting diodes (LEDS) with superior spatial color homogeneity (SCH) have been investigated.In this paper,a new method of packaging of white pc-LEDs that employs a selfexpo