【摘 要】
：
The microstructures and the mechanical properties of the medium manganese steel experienced warm rolling and annealing are investigated.And the transformation of reverted austenite in the steel is inv
【机 构】
：
National Engineering Research Center for Advanced Rolling Technology,University of Science and Techn
论文部分内容阅读
The microstructures and the mechanical properties of the medium manganese steel experienced warm rolling and annealing are investigated.And the transformation of reverted austenite in the steel is investigated by means of tensile testing in stages,scanning electron microscopy ( SEM) and X -rays diffraction ( XRD).It is shown that warm rolling and annealing after the hot rolling result in more reverted austenite,and excellent mechanical properties are gained with 859 MPa strength and 36% elongation.In the earlier stage of tensile deformation,serrate flow stress behavior is obviously observed because of the sustained TRIP effect produced by reverted austenite.And in the later stage of tensile deformation,serrate flow stress behavior disappeared.The ultrafine grain ferrite and martensite produce plastic deformation,and dislocation strengthening in the martensite becomes the main strengthening mechanism.
其他文献
It is well known that the corrosion resistance of galvanized steel can be greatly improved by means of suitable chromate based passivation.The effectiveness of chromate based passivation is without qu
It is well-known that the electrical steel of 6.5% Si has applications such as on making of high- frequency transformer due to its high electrical resistivity,low core losses,near zero magnetostrictio
Recent research that emphasizes electron backscatter diffraction ( EBSD) as a characterization tool has clarified the microstructure of dislocated martensitic steel formed by quenching moderate to lar
Requirement on the weight saving of automobiles has further been energetic for global environment and for saving natural resources.The steel which has tensile strength ( TS) more than 1,000 MPa and TS
使用真空直流磁控溅射技术在DI材表面制备Al膜,并对镀铝DI材的可加工性与制备条件及铝膜的厚度之间的关系进行了研究.杯凸和冲杯试验表明铝膜沉积时的基板温度和膜厚对铝膜的附着力和可加工性有较大影响,当铝膜厚度大于2 μm时,铝膜的附着力变差.当基板温度从室温升至200℃时,铝膜的附着性和冲压性能有明显提升。
Steel is the dominant construction material for most industrial goods such as equipment,structures,buildings or vehicles.Although there have been great advances in steel technology over the last 4 dec
Over the last decade press hardening process has become a key lightweight technology for the automotive industry worldwide because it offers ultra - high strength up to 1 500 MPa for the safety compon
Chain-Die Forming ( CDF),a novel sheet metal forming technology,has been proposed and developed recently in Australia.The primitive objective of CDF was to overcome the theoretical and practical limit
Our research program seeks to understand the influence of hydrogen on steels for the hydrogen economy.The present paucity of affordable hydrogen-proof materials poses strong technological and economic
采用SEM+EDS试验分析了IF钢冶炼过程中不同阶段钢水夹杂物的形貌和类型,对比了水口絮瘤物与中间包钢水夹杂物的类型情况.研究结果表明：炉后大包钢水中夹杂物一般为球状或块状Mn-Fe-O复合夹杂物,RH铝脱氧后夹杂物演变成树枝状的Al2O3夹杂物,没有发现Mn-Fe-O复合夹杂物,钢水中加入钛铁后,夹杂物包括Al2O3系和Al2O3-TiO2系复合夹杂物,Al2O3系和Al2O3-TiO2系复合夹