【摘 要】
：
The mass fraction of 30% SiC particles reinforced Al-Si matrix composite was prepared by One-way press method, sintering and hot extrusion.The microstructure and mechanical properties of SiCp/Al-Si ma
【机 构】
：
School of Materials Science and Engineering,Henan University of Science and Technology,Luoyang 47102
【出 处】
：
第二届中国国际复合材料科技大会 (CCCM-2)
论文部分内容阅读
The mass fraction of 30% SiC particles reinforced Al-Si matrix composite was prepared by One-way press method, sintering and hot extrusion.The microstructure and mechanical properties of SiCp/Al-Si matrix composite under different aging temperatures were investigated by means of SEM and XRD, tensile test analysis.
其他文献
快速城市化地区是人文因素最密集、人文因素与自然因素交互作用最复杂、各类地理空间转换最频繁、空间冲突最激烈、空间风险最突出的地区,也是一个边界动态变化明显,各种物质流、能量流、信息流高度活跃的开放的复杂巨系统,是地球表层最复杂的人地关系地域系统.研究快速城市化地区人地相互作用的空间效应有利于揭示该类区域的演变机制并引导其健康发展.本文以人地关系地域系统理论、可持续发展理论、冲突理论、博弈论等为指导,
C/SiC composites fabricated by melt infiltration process are potential materials for the applications of high-performance structures.Porous C/C is often used as the preform for the fabrication of C/Si
Fiber-matrix interface of C/SiC composites prepared via precursor infiltration and pyrolysis was modified by BN interphase on degummed fibers by decomposing borazineand heat-treated BN interphase.Mode
Zirconium carbide (ZrC) is a potential candidate for ultra-high temperature applications, due to its promising cohesive properties and electronic properties.However, for the strong covalent bonding, Z
通过超重力燃烧合成熔渗技术成功制备了两种钨丝增强铜基复合材料，一种是细钨丝堆垛无序复合，另一种是粗钨丝排列有序复合。并用三点弯曲法测试了抗弯强度，结果表明：超重力燃烧合成熔渗技术制备的铜基复合材料中，基体铜具有较强的择优取向，从而导致平行和垂直超重力方向的性能差异较大。细钨丝堆垛无序复合有利于降低铜基体的取向程度，增加复合材料的整体性能，粗钨丝排列有序复合有利于增强平行于超重力方向的强度。
本文采用单向冷压、烧结和热挤压方法制备30％(质量分数)SiCp/Al-Si基复合材料,利用SEM、XRD、拉伸强度等测试方法研究了不同时效温度对SiCp/Al-Si复合材料微观组织及力学性能影响规律.结果 表明：复合材料在500℃+4h固溶处理后,180℃时效6小时,Si相析出数量达到极值,材料强度达到最大值285MPa.随着时效温度的增加,析出相颗粒尺寸增大,材料的延伸率下降；断口韧窝增大,试
采用粉末冶金法制备了体积分数不同的微米碳化硅颗粒和纳米碳化硅颗粒混杂增强的铝基复合材料,采用扫描电镜和透射电镜对复合材料的微观组织进行表征,并对复合材料的拉伸性能进行测试,分析球磨混粉工艺参数对复合材料组织与性能的影响。结果 表明：碳化硅含量为10％,微纳米颗粒含量比为5∶1,球磨时间为8h的复合材料中微纳米碳化硅颗粒分布均匀,并与基体合金的界面结合良好。与粉末冶金法制备的基体合金相比,混杂增强复
采用搅拌摩擦加工技术制备了多壁碳纳米管增强铝基(MWCNTs/Al)复合材料,研究了碳纳米管含量对复合材料力学性能的影响规律.结果 表明：MWCNTs的添加对铝基复合材料的力学性能作用明显,随着MWCNTs含量的增加,MWCNTs/Al复合材料的硬度、弹性模量、强度都逐渐提高；当碳纳米管含量为6.6Vol.％时,复合材料强度达218MPa,为基体材料的2.24倍；随MWCNTs含量的增加,MWCN
W fiber reinforced copper materials fabricated by combustion synthesis melt infiltration under ultra-high gravity.Two styles for W fibers were designed.One is disordered stacking.Another is ordered ar
In this paper, the molybdenum coating was successfully deposited on the surface of diamond particles by direct current magnetron sputtering method, its surface morphology and chemical composition were