【摘 要】
：
The Medical Research Council and the UK Clinical Research Collaboration awarded a ＃4 million grant to the consortium of academic and industrial researchers to improve seYUal health through the use of
【机 构】
：
Centre for Electronic Systems Research (CESR) UK
【出 处】
：
2011传感器与MEMS技术产业化国际研讨会
论文部分内容阅读
The Medical Research Council and the UK Clinical Research Collaboration awarded a ＃4 million grant to the consortium of academic and industrial researchers to improve seYUal health through the use of new technologies. Brunel University in partnership with St. Georges Medical School, aIMSto develop self-test devices that can quickly identify any infection and communicate the information wirelessly with a mobile phone or computer to help patients understand and seek out treatment they might need.
其他文献
众所周知，在溴化锂溶液中添加纳米微粒可以有效地提高其传热和传质特性，但是添加纳米材料的溶液的稳定性是很重要的一环。本文在原有的制备流程基础上，针对58％溴化锂溶液，通过重力沉降试验研究了制备添加纳米微粒的溴化锂溶液的流程，完善了原有的制备流程，得出了制备溴化锂纳米溶液更加合理的流程，得到纳米微粒和分散剂的稳定性试验结果。由于实际运行的溴化锂吸收式制冷机中溶液的温度会在40℃到150℃间不断变化。因
介绍了上海市检测中心冰蓄冷空调系统设计方案及特点，该系统测试结果及实际运行效果表明，采用双工况三级压缩离心式冷水机组与不完全冻结式蓄冰盘管相结合，系统运行稳定可靠。由于离心式冷水机组能效比高，故该冰蓄冷空调系统节能效果显著。
采用数值模拟方法对自然置换通风、自然层状通风、自然顶部通风三种自然通风方式室内温度场和速度场进行研究，以获取三种自然通风方式中室内热舒适性，寻求各自然通风方式适用范围。研究结果显示，三种自然通风方式中人体头部与脚踝之间垂直温差均小于5℃，满足人体热舒适对垂直温差的要求。自然置换通风、自然顶部通风在人体呼吸区高度上气流速度分布比较均匀，除进风口以及出风口附近区域其他区域气流速度均小于引起人体不舒适的
利用等离子喷涂技术制备NiCr 作为粘接层的P7412 陶瓷涂层。采用失重法研究了涂层在3.5％NaCl 溶液中的腐蚀速率。用SEM 观察涂层腐蚀前后的表面形貌，并用动电位极化曲线和电化学阻抗谱（EIS）技术研究涂层的腐蚀机理。根据陶瓷涂层的特殊结构，建立等效电路图并进行拟合分析。结果表明，粘接底层/基体界面腐蚀产物会影响涂层失重。氧化膜的生长与溶解以及腐蚀二次产物的积累共同导致了涂层重量出现周期
Continuous inkjet (CIJ) technology has the advantage of much higher speed, better reliability, and wider ink and substrate latitude compared to drop-on-demand (DOD) inkjet technology. KODAK Stream Ink
MEMS Industry is growing double digits now and will continue its fast growth for the next decade.Bosch is one of the earliest pioneers of the MEMS technology, and invented the famous Bosch Process.MEM
Plasma, eYCited with microwave energy, has Very interesting properties which are in direct correlation with the eYCitation frequency. This is due to the reachable high electron density, which itself h
This presentation introduces a new IC architecture and design technique which can be widely used for MEMS based sensors and wireless applications. The presented digital predistortion technique can ach
After many years developing, MEMS is getting blooming in consumer filed and become one of the driving force of new applications, especially Internet of Things since 2009. As the smart nodes on the IOT
There is a big boost in demand of MEMS in the last two years driven by their use in consumer applications such as smart phones, tablets and gaming consoles. Yole Developpment predicts about 14％compoun