Estimation method for random sonic fatigue life of thin-walled structure of a combustor liner based

来源 :2013年LMS中国用户大会 | 被引量 : 0次 | 上传用户:dajiange
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
  As to the sonic fatigue problem of an acro-cngine combustor liner structure undcr the random a- coustic loadings,an cffective method for predicting the fatigue life of a structure undcr random loadings was studicd.Firstly,the probability distribution of Von Mises strcss of thin-wallcd structure undcr random loadings was studicd,analysis suggestcd that probability density function of Von Miscs stress proccss accord approximately with two-paramctcr Weibull distribution.The formula for calculating Weibull parameters were givcn.Based on the Miner linear theory,the method for predicting the random sonic fatigue life bascd on the stress probability dcnsity was developed,and the model for fatiguc life prediction was constructcd.As an cxamplc,an acro-cngine combustor lincr structure was considercd.The powcr spcctrum dcnsity (PSD) of the vibrational stress response was calculated by using the coupled FEM/BEM (finite clemcnt method/boundary elcmcnt mcthod) model,the fatiguc life was cstimated by using the constructed model.And considcring the influence of the wide frequency band,the calculated results were modified.Comparetive analysis shows that the es-timated results of sonic fatiguc of the combustor liner structure by using Weibull distribution of Von Mises strcss are more conservative than using Dirlik distribution to some extend.The rcsults show that the mcthods prcscntcd in this papcr are practical for the random fatigue life analysis of the acronautical thin-wallcd struc-turcs.
其他文献
应用LMS Virtual.Lab软件的多体动力学分析模块Motion,对大型水陆两栖飞机的主起落架收放过程进行了仿真分析,得到了收放机构的驱动做动筒需要输出的载荷,为收放机构的理论设
本文以RT-Flex 60C柴油机为对象,根据柴油机工作过程数值计算理论,利用AMESim软件建立了船用低速二冲程柴油机仿真模型.仿真结果表明,所建立的模型能有效反映柴油机工作特性,
使用SAMCEF ROTOR转子动力学分析软件,采用有限元分析方法进行某试验机组转子动力学特性分析.通过轴系探索,得出了一些工程应用结论.
针对某型号车用球轴承涡轮增压器,利用密封力与油膜力动力学相似原理,将增压器转子系统中的密封结构视为一种油膜轴承,应用短轴承理论计算得到其刚度和阻尼矩阵并代入模型进
随着大型海上风电场的建设逐步由浅水向深水海域发展,传统固定式基础结构已不能满足海上风机工作性能要求,研究漂浮式风机已成为各国开发海上风能的热点工作.文章采用风机正
风机产业发展迅猛,单机容量的不断增大要求风电机组设计中必须进行建模仿真及优化.传动链作为核心部件,对风电机组的优化应该首先从传动链着手.风机仿真的商业软件众多,本文
利用SAMCEF/ROTOR软件建立了1-0-1支承结构高变形能柔性转子梁单元有限元模型,得出了转子的临界转速、振型、响应值.通过改变涡轮盘安装位置获得了转子系统动力特性随涡轮盘
本文利用LMS软件对排气尾口辐射噪声进行测试,并对测试结果进行分析.根据分析原因对排气系统进行优化改进,并得出排气尾管长度对排气尾口辐射噪声的影响规律.最后通过加长排
用CAE方法分析某汽车发动机油底壳的振动噪声特性.基于油底壳连接螺栓处的单位加速度激励,通过FEA得到油底壳外表面的速度响应,应用LMS Virtual.Lab软件计算了油底壳外表面的
密封条是车身结构的重要组成部分,其隔声性能对车身结构的NVH性能至关重要.首先对某车门密封条进行非线性准静态分析,获取各压缩率下的密封条变形及应力分布情况.然后对变形