Interaction of human fibroblasts with electrospun composites gelatin/PLLA, chitosan/PLLA and PLLA fi

来源 :2012 Postdoctoral Symposium of China on Materials Science & | 被引量 : 0次 | 上传用户:blueskyjandy
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
  Highly porous ultrafine electrospun scaffolds, gelatin/PLLA and chitosan/PLLA were prepared by blending gelatin and PLLA, chitosan and PLLA respectively.This bilaminar texture is suitable for preparing a bilayer skin substitute.The characterization of gelatin/PLLA and chitosan/PLLA scaffolds were examined by scanning electron microscopy (SEM) and compared respectively.The biocompatibilities of the gelatin/PLLA and chitosan/PLLA scaffolds were assessed by attachment, proliferation and viability of cells on them.The human fibroblasts cell line WI-38 was inoculated on gelatin/PLLA and chitosan/PLLA scaffolds, pure PLLA scaffolds as control.Our study indicated that over 30% WI-38 cells could attach to the gelatin/PLLA and chitosar/PLLA scaffolds at 2h after seeding, while the attachment of the cells was only 15% on PLLA scaffolds.Both gelatin/PLLA and chitosan/PLLA scaffolds also exhibited a very good ability for proliferation of WI-38 cells.Cell growth on the gelatin/PLLA and chitosan/PLLA scaffolds showed dramatic improvement, indicating a much better biocompatibility in the blends contributed by gelatin and chitosan.MTT assay also demonstrated gelatin/PLLA showed better ability to enhance the growth and functions of the cells.These assays suggest that the electrospun gelatin/PLLA and chitosan/PLLA scaffolds are promising biomaterials with great biocompatibility for the development of skin tissue engineering.
其他文献
基于主从控制结构的单针气动刻印装置包括硬件方案和软件方案,将单针刻印装置置于生产线考虑,硬件方案重点指主从控制结构;软件方案重点指EMCM_L0的软件架构,由于EMCM_L0移植了WINCE6.0 操作系统,对于WINCE6.0下实现的单体设备,重点考虑开机启动和应用程序组件化两个方面;对于单针气动刻印装置来说,在金属产品上打标是其基本功能,设计了基于Arthur绘图系统的动态字库方案,从而刻印内
对于热轧生产线来说,其变速、变载和工艺有别于冷轧生产线,热轧轧制过程工艺参数对于设备的振动影响较大。开展热轧生产线设备状态集中监控工作需要研究设备、工艺、故障履历、故障的可诊断性等,选择针对热性的设备监测和诊断方法。本文通过对热轧生产线设备状态把握的关键技术研究与成功实践,形成了热轧区域设备状态集中监控系统解决方案,性能指标达到国际先进水平。
主要叙述了特钢厂800轧线大棒锯夹紧装置的结构形式及工作原理。总结了该装置使用以来由于设备缺陷而产生的故障,并对部分改进方案的实施性、可靠性进行了分析,提出了存在的问题和今后工作的方向。
本文重点叙述了首钢迁钢炼钢厂板坯火焰清理系统主体设备。现以首钢迁钢炼钢厂板坯火焰清理系统为例,详细地介绍板坯火焰清理系统主要设备的结构特点,技术性能,设计选型。
针对某烧结厂烧结机栏板断裂的问题,本文采用ANSYS 有限元软件中的热-机耦合的方法,首先建立了栏板的三维实体有限元模型,在此基础上模拟了栏板在不同时刻温度作用下各部位温度场及应力场的变化,并结合栏板材料的金相组织分析,找出了栏板断裂的原因,即栏板结构的安全裕度不大,但不会引起栏板裂纹;栏板材料的石墨面积率仅为0.1 左右,球状修正系数为0,基本无球化,这是造成栏板断裂的主要原因。
将连退机组平整机1 号机架入口除尘装置进行改进,改进后的吸尘装置为22mm×1200mm 的鸭嘴形吸尘口,流速可达到25~30m/s,同时增设气动装置将伸缩滑动式吸尘口,在工作时可运动到距支承辊和工作辊相切线 20~30mm 距离,并采用波纹管降低了除尘风管的振动,充分保证除尘效果。进而解决了由粉尘造成的带钢C90 缺陷,机组速度也由原来的300mpm 提高到500mpm,一方面速度的提高增加了生
根据连铸机推钢机的设计经验,介绍液压推钢机的主要参数、结构技术特点,指出设计中应注意的问题。
线材的捆扎在我国属于一个薄弱环节,各大钢铁企业主要依靠进口国外的自动打捆设备。自动打捆设备使用及维护缺少经验借鉴,为保证生产的顺利进行,除配置一台自动打捆设备外,高速线材生产线再配置一台半自动打捆机是目前经济的选择。现有半自动打捆机在结构和功能上存在着若干不足,为此设计了一种新型的对称挤压方式的半自动打捆机。本文主要介绍了此种打捆机的工作原理、优点、结构组成等。
The objective was to attempt to develop and evaluate the porous medical implant scaffolds designed via digital method and fabricated by laser additive manufacturing.A porous artificial femur model and
The phase field method is applied to study the microstructure evolution of Ni4Ti3 precipitates during stress-free and stress-assisted aging of bi-crystalline NiTi shape memory alloys (SAMs) with two d