【摘 要】
：
The thin slab continuous casting and rolling production line in Tangshan Iron and Steelmaking Company ( TISCO) has been in operation for ten years,and the annual yield in past one year had been more t
【机 构】
：
National Engineering Research Center of Continuous Casting Technology,Central Iron and Steel Researc
论文部分内容阅读
The thin slab continuous casting and rolling production line in Tangshan Iron and Steelmaking Company ( TISCO) has been in operation for ten years,and the annual yield in past one year had been more than 3 million tons that may be a world s record in all similar production lines.With change of steel market situation,the improvement of product quality and the development of new steel grades in the thin slab continuous casting and rolling line had been the main focus gradually.Surface longitudinal crack and other defects in the slab are always serious quality problems for thin slab continuous caster,and in order to solve the longitudinal crack problem under the condition that adopting funnel-shape mould for the thin slab casting,the formation mechanism of surface longitudinal crack was investigated.The process characteristic of funnel-shape mould and determination of funnel shape for low carbon casting and medium carbon casting were analysed,and the results in present paper were a good theoretical foundation on the control of surface longitudinal crack defect.Moreover,the optimized physicochemical properties of mould powder for different steel grades were investigated simultaneously during the selecting test of funnel-shape mould,plus the physicochemical properties difference of the mould powder for normal slab caster and thin slab caster was compared,the shape-optimized submerged nozzles and the application performance of which in TISCO were introduced in the paper.Furthermore,the process characteristic,the product quality and the key control rules of high carbon steel( C = 0.40% - 0.70% ) in the thin slab caster were analysed.
其他文献
本实验室分别通过相转移法和原位热聚介工艺制备得到了PVFM基的凝胶聚介物电解质。研究发现:以MDI作为化学交联剂通过相转移法制备的PVFM基聚介物薄膜热稳定性高、机械强度好、吸液率高，通过溶胀液态电解质可以形成稳定的凝胶聚介物电解质;而PVFM自接溶于液态电解质可以在LiPF6的催化作用下发生原位热聚介得到凝胶聚介物电解质。所制备得到的电解质离子电导率均可达10-4-10-3s/cm，电化学稳定窗
钛酸锂Li4Ti5O12作为锂离子电池负极材料具有安全性好、循环寿命长以及环境友好的优点,在混合动力汽车以及储能电池等领域具有极其广阔的应用前景。在研究中发现,通过采用超细TiO2(10nm左右)作为钛源,以及控制原料中的Li:Ti摩尔比和制备条件,可以合成出不同理化度的Li4+xTi5O12/C.将这些Li4+xTi5O12/C组装成研究电池,其首次库仑效率均大于100％,同时还具有优异的循环性
本文以葡萄糖为碳源,采用机械活化辅助固相法制备了LiVPO4F/C正极材料,并研究了不同碳含量对LiVPO4F/C晶体结构、物理和电化学性能的影响。实验结果表明,LiVPO4F颗粒随着碳含量的增大变得细小、均匀;LiVPO4F/C在0.1C下的首次放电容量随着碳含量的增大先增大后减少,碳含量为8.8wt％时,首次放电比容量达到最大135.7mAh/g,并具有良好的循环性能和倍率性能。
本文成功合成了Na4Fe(CN)6/NaCl固溶体.固溶体内部产生的阳离子空位极大地促进了材料的电子导电性和钠离子传导速率.将该材料作为正极与钠片组装成钠离子电池,具有较高的容量,很好的倍率性能和循环性能.因此,Na4Fe(CN)6/NaCl固溶体是一种低成本、环境友好的钠离子电池正极材料.
采用基于液相还原沉积的一步法合成石墨烯包覆硫微粒复合材料.该材料粒径分布均匀,硫微粒和石墨烯之间形成稳固的核壳结构.利用XRD,Raman spectrum,SEM,TGA,EDS等多种物测试法对合成的材料进行了详细表征.电化学测试表明,使用该复合材料(含硫量达到83.3wt％)作为锂硫电池的正极材料具有高比容量、优越的倍率性能和良好的循环性能等优点.在0.75,2.0,3.0和6.0C的倍率条件
CaO-based slag is generally used to remove impurities in steel.For producing a CaO-based slag,various solid oxides such as lime and dolomite are added as flux.It is well known that the dissolution rat
碳对钢的力学性能影响很大，是钢中最重要的合金元素之一，脱碳就成为炼钢过程中最重要的反应之一.对AOD法的熔池混合和脱碳过程进行了模拟试验研究,在其他条件一定的情况下,考察了AOD炉侧吹喷枪的气量、夹角变化对均混时间、脱碳速率的影响.试验结果表明,吹炼过程中熔池液体处于充分的搅拌和循环运动状态,熔池内没有明显的死区,混合效果好,混合时间短.侧吹主枪的吹气量对熔池内流体的流动和混合有决定性的影响,侧吹
对DC03钢在中间包长水口和浸入式水口,铸坯的边缘、1/4处和中心处分别取样,用SEM-EDS观察钢中夹杂物,在浸入式水口、铸坯中特别是铸坯中心处观察到大量外面包裹一层碳化物、中心为钙铝酸盐的双层夹杂物,将这类夹杂物称之为碳化夹杂物或者石墨化夹杂物.通过面扫描和线扫描发现碳化物两种结构：一种为CaC2,另一种为铁碳化合物（渗碳体和石墨）.从热力学上分析了碳化夹杂物形成的条件,由于钢中碳为易偏析元素
Surface quality of cast products it s the very key to a successful final product,especially in the automotive industry.For this to be achieved it is necessary to have control of casting parameters an
唐钢第二钢轧厂集成应用七项技术,建立起了一个高效率、低成本的建筑用长材洁净钢生产平台.通过全铁水扒渣、高效转炉吹炼、铸钢“三稳”和“三定”等,一次拉碳、硫、磷成分命中率达到93％以上，连铸有效作业率达96％以上;通过钢包全程加盖、连铸坯高温直送、定重供坯、切分轧制等,出钢温度降低至1635℃,铸坯入加热炉温度在800℃以上及热装比例高于90％,棒材成材率达97.05％,各工序能耗大幅下降.该平台建