颈胸部肿瘤应用头颈肩体热塑膜放疗的摆位误差

来源 :江苏医药 | 被引量 : 0次 | 上传用户:xiaojas
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
rn目的利用射野影像系统(EPID)测量颈胸部肿瘤应用头颈肩体热塑膜放疗的摆位误差,并计算出计划靶区(PTV)的外扩范围。方法放射治疗的颈胸部恶性肿瘤患者20例,制作头颈肩体热塑膜,通过比较计划射野参考图像(DRR)和实际射野验证图像(EPI)相关骨性标记的位置偏移,计算出三维方向的摆位误差,并由公式MPTV=2.5Σ+0.7σ分别计算出不考虑与考虑靶区内扩边的具体MPTV值。结果 20例患者在三维方向上的摆位系统误差标准差分别为0.95mm、0.26mm和0.57mm,随机误差标准差分别为1.46mm、0.53mm和0.99mm。不考虑靶区内扩边的MPTV值分别为3.4mm、1.0mm和2.1mm,考虑的为7.38mm、6.62mm和6.88mm。结论颈胸部肿瘤患者应用头颈肩体热塑膜固定,体位重复性和准确性均相对较高;实测本院放疗中心的MPTV值,使制定的精确放疗计划更具科学性。“,”Objective To establish a method using electronic portal imaging device(EPID) to acquire the setup errors and to calculate the margin of planning target volume(MPTV) for neck-thoracic tumor in radiotherapy.Methods Twenty patients with neck-thoracic tumors were fixed by head-neck-shouder-body theroplastic mask.Setup errors in X(medio-lateral),Y(antero-posterior) and Z(cranio-caudal) direction were calculated by comparing the position offset of the relevant osseous marks between DRR and EPI.According to the formulation,the size of MPTV with or without consideration of organ motion was calculated as well.Results The standard deviations of systematic errors(Σ)were 0.95 mm,0.26 mm and 0.57 mm at X,Y and Z direction,respectively.The standard deviations of random errors(σ) were 1.46 mm,0.53 mm and 0.99 mm at X,Y and Z direction,respectively.Without consideration of organ motion,the sizes of MPTV were 3.4 mm,1.0 mm and 2.1 mm at X,Y and Z direction,respectively.With consideration of organ motion,the sizes of MPTV were 7.38 mm,6.62 mm and 6.88 mm at X,Y and Z direction,respectively.Conclusion Fix ation with head-neck-shouder-body theroplastic mask could provide a relatively higher assurance in position repeatability and accuracy for neck-thoracic tumor patients.Actually measuring the value of MPTV is more scientific in planning the radiotherapy regime.
其他文献
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
对TLM钛合金进行了不同热处理条件下的室温硬度测试、杯突试验和弯曲试验。结果表明,固溶处理后合金板材的杯突值IE为4.7~5.8 mm,最大弯曲角为180°,显微硬度为226~236 HV0.1
采用Al-Mg、V-Ti和Al-Mg+V-Ti对3.81wt%C-15wt%Cr铸铁进行变质处理,研究不同变质剂对高铬铸铁初生碳化物的变质机理。结果表明,Al-Mg变质的机理主要表现为脱氧脱硫净化铁液,
代编者按:探索地球深部奥秘的科学钻探工程,分为大陆科学钻探(CSD)和大洋科学钻探(ODP)两大领域。中国大陆科学钻探于1979年由原地矿部倡议,已过去了二十个年头,国家很支持,国际大陆科学钻探计划
皖江示范区设立以来,承接产业转移数量快速,质量不断提升,成为中部崛起的重要增长极。依托皖江示范区区位和资源禀赋优势,坚持特色承接、集群承接、创新承接、联动承接、绿色
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊