普罗布考对冠状动脉球囊损伤后管壁原癌基因c-myc 表达的影响

来源 :中国新药杂志 | 被引量 : 0次 | 上传用户:pdscyz
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
目的 :通过建立猪冠状动脉球囊损伤模型 ,观察普罗布考对血管内膜增生及管壁原癌基因c myc表达的影响。方法 :选用雌性NewYorkshire良种猪 19头 ,随机分为 2组 ,对照组 11头 ,普罗布考组 8头 ,均行冠状动脉球囊扩张术 ,术后喂饲 6周 ,重复冠状动脉造影后处死动物。普罗布考组于术前 4周给予普罗布考 1g ,bid ,至实验结束。常规病理制片 ,观察形态学变化 ,采用RT PCR的方法检测c mycmRNA的表达强度。 结果 :对照组损伤动脉内膜可见大量平滑肌细胞增生 ,呈偏心性增厚 ,普罗布考组内膜增厚程度明显减低。对照组c mycmRNA相对表达强度为 (2 .73± 0 .5 1) ,明显高于正常动脉 [(0 .82± 0 .0 9) ,P <0 .0 5 ],普罗布考组c mycmRNA相对表达强度为 (1.44± 0 .2 5 ) ,较对照组减弱 (P <0 .0 5 ) ,但仍高于正常动脉 (P <0 .0 5 )。结论 :普罗布考具有抑制冠状动脉球囊损伤后c myc表达和内膜增生的作用 OBJECTIVE : To observe the effect of probucol on the intimal hyperplasia and the expression of proto-oncogene c myc in porcine coronary arteries by establishing a balloon injury model of porcine coronary arteries. Methods: Thirteen female New Yorkshire breeders were randomly divided into two groups: 11 in the control group and 8 in the probucol group. All patients underwent coronary balloon dilation. After 6 weeks of postoperative feeding, they were sacrificed after coronary angiography. animal. The probucol group was given probucol 1g 4 weeks before surgery and bid was completed until the end of the experiment. Routine pathology, observed morphological changes, using RT PCR method to detect the expression of c myc mRNA. RESULTS: A large number of smooth muscle cells in the intima of the injured arteries in the control group showed hyperplasia and thickening, and the degree of intimal thickening in the probucol group was significantly reduced. The relative expression intensity of c myc mRNA in the control group was (2.73±0.51), which was significantly higher than that in the normal artery [(0.82±0.09), P<0.05]. The c myc mRNA was detected in the probucol group. The relative expression intensity was (1.44±0.55), which was lower than that of the control group (P<0.05) but still higher than that of the normal artery (P<0.05). Conclusion :Probucol can inhibit the expression of c myc and intimal hyperplasia after coronary balloon injury
其他文献
采用近似因子分解法、光滑粒子流体动力学法进行挤压铸造充型过程数值模拟研究。模拟结果显示,近似因子分解法、光滑粒子流体动力学法(SPH)计算结果与Win-cast铸造模拟软件计算
介绍B15B阀体产品结构,模具结构以及生产过程中出现的问题.运用模流分析,对模具的进料系统及排溢系统做了分析改进,解决了节流阀体在生产过程中出现的问题,有效降低了产品废
以某铝压铸件油底壳螺纹衬套装配工序为例,介绍了余料回收防错装置的开发及应用.通过防错装置的开发,从而减少因为漏除余料或者余料留在压铸件内导致重新检查时间,减少不良件
采用ProCAST软件对熔模铸造汽车转向臂的浇注系统进行设计,并对其浇注过程进行模拟仿真.通过仿真结果分析,对浇注方案进行了优化,优化后的浇注系统充分考虑到了熔体的补缩.然
研究了Al含量对Al-Mg2Si复合涂层耐磨蚀性能的影响.采用电化学测试仪、腐蚀-磨损试验机观察Al含量为80%、60%、40%和20%的Al-Mg2Si涂层的开路电位和摩擦因数,并采用扫描电镜(SEM)
测量和分析了不同脉冲超声功率下ZL205A铝合金在距变幅杆端面不同纵向深度下组织的显微硬度,研究了脉冲超声功率对不同部位显微硬度的影响,并建立了ZL205A合金显微硬度与脉冲
进行了脉冲磁场下制备Al-20Si功能梯度材料的研究,分析了脉冲电压、脉冲频率、模具预热温度及浇注温度对初生Si形态和分布的影响.结果表明,利用脉冲磁场成功制备了Al-20Si功
在应变速率为10-1~10-1s-1和温度为250~450℃范围内对2524铝合金板材进行单向热拉伸试验,研究了热变形参数对其显微组织及力学性能的影响.结果表明,当温度为400℃,应变速率为10
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生、测量监控等方面人手,介绍了S226海滨大桥
采用光学显微镜(OM)、涡流电导仪和维氏硬度计等手段,研究了分级时效对Cu-Cr-Zr-Co-Si合金组织和电导率、硬度的影响,并与单级时效处理工艺作比较.结果表明,采用分级时效能够