航空集群“1发2收”协同探测编队构型研究

来源 :飞航导弹 | 被引量 : 0次 | 上传用户:jackieWXM
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
航空集群协同探测问题是集群作战研究的重要内容,其中对集群探测模型的建立和最优构型的确立是难点问题。针对航空集群协同探测编队构型问题,在隐身飞机RCS空间差异性较大的基础上,建立集群协同探测模型。基于空间分割法,对影响集群探测能力的两个重要因素——接收机方位角和收-发雷达之间的基线距离,分别进行仿真分析。结果表明,集群中任一发射机、接收机都能形成一定的探测能力,在探测区域连通条件下,以最大探测面积为指标,将两部接收机部署在发射机正侧方附近,并且对称分布,基线距离约为4倍单机迎头探测距离时,探测面积达到雷达单独作用下的10倍以上。 Collaborative exploration of aviation cluster is an important part of cluster research, in which the establishment of cluster detection model and the establishment of optimal configuration are difficult problems. Aiming at the problem of formation formation of collaborative exploration formation in aviation cluster, a cluster coordination detection model is established based on the large spatial heterogeneity of stealth aircraft RCS. Based on the space division method, two important factors affecting the detection ability of the cluster, ie, the receiver’s azimuth and the baseline distance between the radar and the receiver, are simulated and analyzed respectively. The results show that any transmitter and receiver in the cluster can form a certain detection capability. When the detection area is connected, the two receivers are deployed near the transmitter’s side with the maximum detection area as an indicator, and the symmetry Distribution, the baseline distance of about 4 times the single head-on detection range, the detection area reached more than 10 times under the radar alone.
其他文献
贵州省机械研究所于1984年开始磨料磨具方面的研究工作,为适应贵州省磨料磨具工业发展的需要,于1989年初成立了磨料磨具研究室(第六研究室),该室由具有相当经验的中青年技术
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
切削加工生产目前有三项要求:第一,切削高速化,可提高生产效率,缩短加工时间;第二,采用自动化,实现无人操作,要求必须延长工具寿命,减少更换工具次数;第三,适应于难切削材料
[女人处世]对付压力,就是让自已以更轻松的姿态面对生活为压力改一个好听的名字心理学家建议人们在遇到压力时,不妨从乐观的一面去想比如把压力当作事业向前推进的讯号,或者是一
摘要目的评价双能量CT成像应用虚拟非对比增强(VNC)CT序列量化冠状动脉钙化的可行性。材料与方法本研究获得伦理审查委员会的批准,并符合HIPAA规定。所有病人均签署书面知情
从第一艘航母亮相到歼-20的首次批露,由舰载机首次着舰,再到运-20等一系列代表大国制造和展示国之重器的装备频频亮相,让国人为之鼓舞,极大增强了民族自信心和自豪感。2016年
品位是指品质、档次与水平等。有品位的音乐课堂在于音乐教师在课堂上是否能散发出独特的个性魅力,以自身的专业特长和对课堂独特的驾驭,彰显出鲜明的教学特色;是否充分挖掘
我国中小企业当前普遍存在着设备比较陈旧,技术不够先进的问题。下面围绕新技术的应用谈谈我的看法。一、提高对推广新技术的认识一些新技术,如应用微机的经济型数控、数显
全国第二次等离子弧切割应用技术交流会于1989.10.18~20日在北京煤矿机械厂召开。参加会议的有来自全国的五十九名代表。会议期间有十一名代表宣读了13篇文章,介绍了等离子弧
制作方法:将一块报废的外圆为φ40、厚度为20mm的卡尺研磨块放在车床上,把一面车一凹孔,孔内径为φ34mm,深8mm。另一面上用划线尺划三条平行线,每条间隔10mm。转过90°划一