Bioactive Ca-P scaffolds used for bone reconstruction

来源 :中国有色金属学会会刊 | 被引量 : 0次 | 上传用户:rette
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Bioactive ceramic scaffolds HA*TCP, aimed to be applied in clinic, were evaluated both in vitro and in vivo models. HA*TCP was supposed as a completely biodegradable material and designed as a scaffold to be used for bone reconstruction or regeneration. Materials processing was proposed and physical properties as well as microstructure feature were characterized. Biological postulation of the relationship between seeding density and proliferation, and viability of human osteoblasts cultured on the porous HA*TCP were quantitatively measured. Bone reconstruction was investigated both in vitro and in vivo by using these biodegradable scaffolds with pore sizes ranged in 200-400 μm in diameter. The degradable scaffold supported cellular proliferation of seeded osteoblasts on the scaffold and shown normal differentiated function in vitro. Seeding density is an important factor for cell attachment and proliferation expression and has been considerably discussed. Suitable pore size of the scaffolds is required if promotion of bone reconstruction is desired. Clinical trials show that HA*TCP scaffolds are successful applied for bone reconstruction and regeneration and can be completely degraded in human body in 12 months. This approach suggests the feasibility of using porous HA*TCP scaffold materials for the transplantation of autogenous osteoblasts to regenerate bone tissue.
其他文献
研究了当燃烧波蔓延通过(Ti-2B-60wt%Cu)/(3Ti-2BN-x·Cu)(x=0、10、20、40wt%)两层混合粉料时,稀释剂Cu含量和生坯压制压力p的变化对燃烧波形态和传播速度的影响.经实验测定,
采用化学共沉淀法成功地制备出适用于彩电显象管内荧光体着色的CoxR1-xAl2O4(R=Zn、Mg,x=0.8~1.0)钴蓝颜料:450nm波长处反射率最大提高18.2%,600nm处反射率最大降低5%.通过对该
采用真空浸渍工艺 ,成功地制备了三维编织炭纤维 /环氧复合材料 ,并用金相显微镜对微观结构进行了观察 ,发现基体与纤维间浸润良好。力学试验表明 ,该材料具有良好的力学性能
研究了脉间 Costas FH雷达中用逆离散傅里叶变换 (IDFT)进行信号处理的过程 ,分析了脉间 Costas FH雷达信号不存在距离 -速度耦合的原理 ,讨论并仿真了目标运动对合成距离像
采用 Si- B系组分表面涂层对飞机炭刹车盘进行抗氧化处理 ,涂层中的 B组分在高温下形成的玻璃态B2 O3能有效地愈合涂层及炭材料本身的缺陷 ,抑制其氧化活性点。得到的涂层可
以羧甲基纤维素、酚醛树脂及聚乙烯醇缩丁醛为粘结剂进行了超级活性炭的成型,较为详细地考察了粘结剂添加量及粘接剂种类对所制型炭的堆密度、抗压强度及甲烷吸附性能的影响.
介绍了一种 Fe/ C纳米复合材料的制备方法。二茂铁与萘的混合物在惰性气体 (N2 )保护下于 42 0℃进行自升压共热解反应 ,反应在 42 0℃停留 2 h~ 6 h。可获得一类纳米级 (2 0
改变电流密度在钛合金表面电结晶出磷酸钙预涂层 ,经碱液处理转变为羟基磷灰石 (hydroxyapatite,HA)。扫描电镜 (SEM) ,X射线衍射 (XRD)分析及拉伸实验与模拟体液实验表明 :
研究了热处理对 Ml (Ni Co Mn Al) 4 .76合金电化学性能的影响。结果表明 :在 1 1 73K~ 1 373K下适当的热处理可以显著提高贮氢合金电极的放电容量和高倍率放电性能 ;铸态合金
在不同烧结气氛下制备了Y和YF3掺杂钛酸钡材料,借助于XRD、SEM、XRF和阻温测试分析仪,研究了烧结气氛对Y和YF3掺杂钛酸钡材料结构和性能的影响. 研究结果表明,低氧分压气氛可促