Radial Grip Rigidity of the Matching of Lengthened Shrink-fit Holder and Cutter in High-speed Millin

来源 :Chinese Journal of Mechanical Engineering | 被引量 : 0次 | 上传用户:windcode2009
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present,its design and selection mainly depends on the experience and lacks a correct theoretical guidance.In this paper,attention is focus on the radial grip rigidity of the matching of LSFH and cutter in high speed milling.Based on the experiment modal analysis (EMA) technique,an accurate finite element model of the matching of LSFH and cutter is established firstly.Subsequently,the influence of different interference,grip length and spindle speed on the grip rigidity of LSFH are analyzed.The analysis results show that there is a reasonable interference and grip length between the LSFH and cutter so that to have a steepless grip and have a good radial grip rigidity and at the same time to avoid the strength of LSFH to exceed it’s yield limit which will reduce the precision and service life of LSFH,besides when spindle speed reach a extension the weakening influence of the centrifugal force on the radial grip rigidity of the matching of LSFH and cutter should been taken into account.Finally,the finite element analysis results are verified based on the construction of measurement method of the grip rigidity and the results fit very well.The studies provide a theoretical basis for the design,selection and the serialization and standardization of the matching of LSFH and cutter. Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present, its design and selection mainly depends on the experience and lacks a correct theoretical guidance. In this paper, attention is focus on the radial grip rigidity of the matching LSFH and cutter in high speed milling.Based on the experiment modal analysis (EMA) technique, an accurate finite element model of the matching LSFH and cutter is established first. Subjected, the influence of different interference, grip length and spindle speed on the grip rigidity of LSFH are analyzed. analysis results show that there is a reasonable interference and grip length between the LSFH and cutter so that to have a steep grip and have a good radial grip rigidity and at the same time to avoid the strength of LSFH to exceed it’s yield limit which will reduce the precision and service life of LSFH, besides when spindle speed reach a extension the weak ening influence of the centrifugal force on the radial grip rigidity of the matching LSFH and cutter should been taken into account. Finally, the finite element analysis results are verified based on the construction of measurement method of the grip rigidity and the results fit very well The studies provide a theoretical basis for the design, selection and the serialization and standardization of the matching of LSFH and cutter.
其他文献
通过离子交换、活性炭吸附、硫酸盐沉淀等步骤,建立了从裂变 ̄(99)Tc ̄m发生器洗脱液中分离和测定纯β杂质的方法。化学产额为70%左右。方法已用于裂变 ̄(99)Tc ̄m发生器洗脱液中纯β杂质的常规检定。
气液分层流动沸腾现象是水平加热管道内在低热流和流量条件下常见的现象,提高和改善气液分层流动沸腾换热对于改善换热设备性能具有重要意义.本文通过建立蒸发段水平加热自然
ULTRASOUNDINDUCEDANDLASERENHANCEDCOLDFUSIONCHEMISTRYT.V.Prevenslik(2/EGreeneryCourt,DiscoveryBay,HongKong)Abstract:Thestandar... ULTRASOUNDINDUCEDANDLASERENHANCEDCOLDFUSIONCHEMISTRYT. V. Prevenslik (2 / EGreeneryCourt, DiscoveryBay, HongKong) Abstract: T
期刊
Herschel-Bulkley流体作为非牛顿流体中重要的一类,已广泛应用于工程领域.为了改善LBM对Herschel-Bulkley流体流动模拟时的稳定性和精度,在多松弛时间参数LBM(MRT LBM)的基础
浙江省经济信息中心是浙江省大型专业信息机构,“重振辉煌”行动计划已提出成为全国一流的省级政务决策咨询和信息技术服务机构目标。一年多以来,经过业务整合提升,信息中心
2.10ThermalNeutronReferenceRadiationFieldBaoZongyu;ChenJun;YangXiaoyun;YueQian;RongChaofanXuKun;DingShengyao;ZhaiGungnian;Shi... 2.10ThermalNeutronReferenceRadiationFieldBaoZongyu; ChenJun; YangXiaoyun; YueQian; RongChaofanXuKun; DingShengyao; ZhaiGungni
期刊
PREFERENTIAL SPUTTERING OFCu_(76)Ni_(15)Sn_9WangZhenxial(王震遐);PanJisheng(潘冀生);ZhangJiping(章骥平)(CCAST(WorldLaboratory),P.O.Box8?.. PREFERENTIAL SPUTTERING OFCu_ (76) Ni_ (15) Sn_9WangZhenxial; PanJisheng (Pan Jisheng); ZhangJiping (CCAST (World Laboratory
本文采用数值模拟的方法,研究了激波对斜孔情况下超声速气膜冷却的影响.其中主流马赫数为2.44,冷却流马赫数分别考虑1.2,1.5和1.8三种情况,研究了温度场分布规律及平均冷却效
实现聚合物热导率调控,对扩大其在柔性集成电路热管理中的应用非常重要。过去的十年中,学者们从纳米结构材料的制造方面做了大量工作,但是各种各样的官能团与聚合物导热性质
本文基于MEMS工艺研制了硅基微型脉动热管实验芯片,并搭建了热管流动与传热性能实验测试平台,高速可视化观测了热管内气液两相脉动行为特性与流型演化规律,并探索了工质脉动