【摘 要】
：
A high-precision wavelength controller is presented in this paper. It is necessary to find out the difference between the central wavelength of a tunable fiber Fabry-Perot (FFP) filter and that of the input laser, while the wavelength controller operates
【机 构】
：
HubeiPolytechnicUniversity,Huangshi435003,ChinaWuhanNationalLaboratoryforOptoelectronics,SchoolofOpt
【出 处】
：
OptoelectronicsLetters
论文部分内容阅读
A high-precision wavelength controller is presented in this paper. It is necessary to find out the difference between the central wavelength of a tunable fiber Fabry-Perot (FFP) filter and that of the input laser, while the wavelength controller operates at the states of wavelength-scanning and wavelength-locking modes. Firstly, a dynamic simulation model of tunable FFP filter is established, and the dynamic characteristic of tunable FFP filter modulated by an alternating current (AC) signal is simulated. Then the measuring time at wavelength-scanning mode compared with the theory time is discussed, and this time difference shows the difference between the central wavelength of a tunable FFP filter and that of the input laser. At last, the effects on wavelength-locking precision of time delays, including the time delay of opened-loop circuit, the time constant of the closed-loop circuit and the intrinsic hysteresis of piezoelectric (PZT) element, are analyzed. A wavelength controller of tunable FFP filter is designed and prepared. The experimental results at wavelength-locking mode show that a high locking precision is obtained.
其他文献
通过在石英玻璃的抛光过程中引入α-Al2O3颗粒,对抛光过程中石英工件表面产生的划痕类型和收尾阶段不同粒径杂质颗粒产生的划痕长度进行分析,同时研究了抛光液质量分数和抛光盘结构对石英玻璃抛光质量的影响。结果表明:杂质颗粒需要盘面提供足够大的支撑力才能在工件表面产生划痕,而杂质颗粒所受盘面的支撑力大小取决于其位置高度和共同参与受力的基质颗粒数量;杂质颗粒的位置高度很难掌控,但在相同工艺条件下,使用质量分数为6%的抛光粉和具有多微孔结构的沥青抛光盘可以有效降低划痕的产生概率,并且不会导致抛光表面粗糙度变差或过度
我们的研究和资料报导都证实激光有制癌作用。据此，我们用激光治过一些患者的皮肤肿瘤。光源用脉冲型钕玻璃激光器（脉宽1毫秒，脉冲能量300~760焦耳)。它有一光学系统能将激光导向和集中于受照面积上，还有可见光瞄准的辅助设备。
去年采取了许多重要步骤来改进工业激光器的操作，并取得进一步承认。其中最值得注意的发展是用圆偏振光束提高二氧化碳激光器的切割效率和质量；激光器与计算机数控定位系统一体化趋势的加速；中等功率CO2和YAG激光器用于精密焊接、打孔和切割各种元件方面的增长；装配线上用数千瓦的CO2激光器进行热处理和焊接的势头上升；以及在激光参与下，对几种难加工材料做了成功的实验性试验。
为实现机载光电平台的实时高精度稳定跟踪控制，提出了一种基于改进干扰观测器和模糊逼近的复合自适应补偿控制方法。首先，根据系统的机械结构特点分析了各框架间的运动学耦合关系；考虑到载体扰动的影响，提出了一种基于速度信号的改进干扰观测器结构，并分析了它的工作原理和鲁棒稳定性。然后，针对机械系统中普遍存在的摩擦等干扰现象，设计了基于模糊逼近的复合补偿控制策略以保证系统的跟踪性能。最后，利用Lyapunov稳定性理论证明了系统的全局稳定性和跟踪误差的渐进收敛。实验结果显示，该控制方法具有较高的稳定精度，其跟踪误差可达
主要介绍了块状光学材料电流传感器研究领域自1994年以来在传感头设计方案、理论研究及信号处理方案等方面的新进展。
本文给出了探测器列阵和全息位相光栅在CO_2激光外差探测系统中应用的可行性实验研究结果和分析,为实现实用化提供了重要的依据。
Based on fractional Talbot effect, Talbot grating is adopted to realize spatial color separation with high light efficiency. For red and green colors, a two-step Talbot grating is optimized and the light efficiency reaches over 95%. The two-step Talbot gr
在厚膜多孔硅(PS)/氧化多孔硅(OPS)衬底上,结合聚酰亚胺涂层改善表面,研制低损耗、高性能射频(RF)/微波(MW)共平面波导CPW(Coplanar Waveguide).通过在N和P型硅上形成不同厚度PS膜,并对其上的CPW进行分析比较,厚膜PS与石英的共面波导插入损耗非常接近,远小于在2000Ω·cm高阻硅上形成的多晶硅-氧化硅组合衬底:在0-33GHz范围,插入损耗小于5dB/1.2cm;33-40GHz范围,小于7.5dB/1.2cm.
A novel intermediate connector (IC) was formed which was composed of aluminum (Al, 3 nm)/1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile (HAT-CN). The 3-nm-thick Al in the IC is certified to efficiently generate in-trinsic charge carriers, and the HAT-C