【摘 要】
：
The present study reports the titanium dioxide (TiO2) films synthesized from TiCl3 precursor on ITO glass substrates using two electrochemical techniques, namely direct electro-deposition (DE) and pulse electro-deposition (PE). The synthesis po
【机 构】
：
Laboratoired’électrochimieetmatériaux(LEM),FacultédeTechnologie,Départementdegéniedesprocédés,Univer
【出 处】
：
OptoelectronicsLetters
论文部分内容阅读
The present study reports the titanium dioxide (TiO2) films synthesized from TiCl3 precursor on ITO glass substrates using two electrochemical techniques, namely direct electro-deposition (DE) and pulse electro-deposition (PE). The synthesis potential during the time-on (Ton) period was fixed at -1.5 V. However, the open-circuit potential was applied during the time-off (Toff) period. The effect of the technique of electro-deposition and Toff duration on the properties of TiO2 films and their photoelectron-catalytic activity were investigated. The obtained films were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-VIS spectrometer, and photocurrent measurement respectively. It is found that the use of the PE technique at different Toff improves the properties of TiO2 films compared to the DE technique. The XRD patterns show the anatase phase with a marked preferential orientation along the (101) direction for all samples. From the SEM analysis, it is seen a significant change from big multigrain agglomerates at DE to a dense film structure and small multigrain agglomerates at different Toff. As the Toff decreases from 3 s to 1 s, the photocurrent response rises and reaches a high value of about 12 mA/cm2. Compared with DE, and under UV light the photocatalytic property of TiO2 film synthesis via PE has been improved in the degradation of methyl orange (MO). Finally, the films deposited at low Toff (Toff =1 s) show a faster degradation of MO.
其他文献
为了提高碳化硅反射镜的光学性能，满足空间光学元器件对碳化硅材料的要求，对碳化硅反射镜表面改性光学性能和表面粗糙度进行了研究。对碳化硅反射镜表面质量和光学性能进行了分析，探讨了对碳化硅反射镜进行表面改性的必要性和改性层材料的选择。阐述了碳化硅反射镜改性后表面质量和光学性能的提高。进行了附着力和温度冲击实验。结果表明：改性后，其可见光波段表面散射率由大于9.3%降低到小于0.5%，反射率由小于88.5%提高到大于98%，大幅度提高了碳化硅反射镜的光学性能，证明碳化硅表面改性反射镜可以满足空间光学元器件的要求。
激光诱发前向转印技术，作为一种微加工手段，具有制备微小结构的能力，目前已经成为微细加工领域的研究热点。通过改变高斯分布激光脉冲功率密度，进行了Cu薄膜在石英玻璃表面的转印实验，并对转印沉积薄膜进行了光学显微镜、扫描电子显微镜(SEM)和X射线光电子能谱(XPS)表面氧化状态分析，探讨了激光脉冲功率密度与沉积薄膜的尺寸、特殊形貌以及薄膜厚度均匀性的关系，并在此基础上研究了激光转印Cu薄膜的机理。结果表明，当激光平均脉冲功率密度达到1×105 W/cm2时，Cu薄膜的转印才可以发生。随着激光脉冲功率密度的增加
数字全息成像由CCD记录数字全息图后经过计算机数值重建物光波场, 这个过程从傅里叶变换角度看等同于数字全息图的频谱分析。讨论了数字成像系统的脉冲响应函数, 并分别推导了其实像、虚像、零级像在平面波和球面波照射下的波前复振幅分布。结果表明, 实像和虚像是移位的夫琅和费衍射分布, 而零级像是CCD光瞳的菲涅耳衍射分布, 且与参考光波前分布无关。
展示了所构建的基于四平面镜的单相机三维(3D)采集系统,介绍了系统所采用的三维扫描的几何光路,分析了从图像解析出高度的3D采集算法、空间分辨率与图像分辨率的关系,也讨论了算法的优化以及3D再现技术。从实验结果可以看出,与采用激光扫描的3D采集系统相比,基于镜像视差的3D采集系统,结构更简单,而且可以同时采集出物体的空间结构和表面纹理颜色,是一种有效的3D采集手段。
Double-weight optical code division multiple access (OCDMA) systems are proposed for studying differentiated quality-of-service transmission. Based on quadratic congruence code (QCC), we construct a one-dimensional double-weight code family, which can be
通过菲佐型干涉系统、直角圆锥反射镜的一次性测量, 可获得圆柱形光学元件整周的面形信息。为实现高精度的面形测量, 实验装置的校准至关重要, 但由于调整机构的缺陷导致圆锥反射镜和被测圆柱的空间方位难以确定, 距离理想位置的任何位置偏差将给测量结果引入严重的测量误差。为去除该系统误差, 要明确各种失调误差的形成原因, 分析其对测量结果的影响。通过圆柱坐标系下数学模型的建立, 推导出偏移误差和旋转误差的变化公式, 并通过Matlab数值模拟和实际测量对其进行验证。结果表明, 利用误差计算公式可以推导出失调误差系数