Frequency-multiplexing photon-counting multi-beam LiDAR

来源 :PhotonicsResearch | 被引量 : 0次 | 上传用户:xiaomai1212
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
We report a frequency-multiplexing method for multi-beam photon-counting light detection and ranging (LiDAR), where only one single-pixel single-photon detector is employed to simultaneously detect the multi-beam echoes. In this frequency-multiplexing multi-beam LiDAR, each beam is from an independent laser source with different repetition rates and independent phases. As a result, the photon counts from different beams could be discriminated from each other due to the strong correlation between the laser pulses and their respective echo photons. A 16-beam LiDAR system was demonstrated in three-dimensional laser imaging with 16 pulsed laser diodes at 850 nm and one single-photon detector based on a Si-avalanche photodiode. This frequency-multiplexing method can greatly reduce the number of single-photon detectors in multi-beam LiDAR systems, which may be useful for low-cost and eye-safe LiDAR applications.
其他文献
In this paper, we propose and demonstrate a dual-beam delay-encoded Doppler spectral domain optical coherence tomography (OCT) system for in vivo measurement of absolute retinal blood velocity and flow with arbitrary orientation. The incident beam
期刊
期刊
本文介绍一种二元(0,1)微分滤波器。它是由两Ronchi光栅交叉迭加而成,因此称之为交叉光栅。它具有制作简便,微分效果好等优点。
期刊
Photoconductive semiconductor switches (PCSSs) are widely used in high power ultra-wideband source applications and precise synchronization control due to their high power low-jitter high-repetition-frequency. In this letter, a 14-mm gap semi-insulating G
贝壳珍珠层高强高韧的优异力学性能主要归因于其独特的异质异构特征。贝壳珍珠层仿生制品具有异质和结构复杂的特点,传统的制造方法无法制备。激光选区熔化(SLM)增材制造技术以其独特的成形特点,成为复杂结构和特定性能制品的成形技术。SLM成形的异质异构界面的结合质量是影响其力学性能的关键因素之一,因此本文针对激光重熔优化工艺对SLM成形316L/IN718异质异构件微观形貌和力学性能的影响进行研究,并对316L单一母材重熔前后的表面质量进行了对比。结果表明:316L重熔优化后的上表面粗糙度从7.1 μm降低到2.
We demonstrate a deep-learning-based fiber imaging system that can transfer real-time artifact-free cell images through a meter-long Anderson localizing optical fiber. The cell samples are illuminated
为了实现高灵敏度、快速、准确鉴定痕量病原菌核酸样品,介绍了一种痕量核酸样品高灵敏度快速测量方法,并发展了一种微流控芯片核酸等温扩增实时分子诊断技术,研制了新型微纳体系生化反应载体芯片。通过表面惰性处理降低芯片表面对生物分子的吸附影响,构建一种大数值孔径、长工作距离的便携式共焦光学检测系统,有效消除背景荧光的影响,提高了检测灵敏度。在微纳升(7 μL~40 nL)试剂消耗反应体系水平,实现检测灵敏度5个DNA分子拷贝数,并以呼吸道感染疾病的大肠埃希氏菌检测为例,开展临床应用研究,满足低成本临床医疗应用需要。
研究了腔内脉冲双向啁啾补偿方法,实现了Ti:Al2O3激光器稳定的低泵浦自锁模运转,将Ar 激光泵浦功率降低到2.4 W,获得了220 mW,36 fs的锁模脉冲输出.
提出一种高斯光束照射下颗粒后向散射光信号的测试方法,对悬浮于流体中不同粒径的玻璃微珠进行了测量,并对测得的脉冲波形进行分析。结果发现,采集的波形基本上符合高斯分布,且波形峰值与粒径有较好的线性关系。对不同颗粒数浓度的粒径为19.2 μm的标准玻璃微珠的信号波形进行实时采集,得到了浓度与脉冲数的对应关系。研究结果表明,所提出的测试方法可以得到颗粒粒径和浓度信息,有望应用于后续激光放大器的腔内检测。