【摘 要】
：
Acid mine drainage presents an important threat to cementitious structures. This study is aimed at investigating the effect of cellulose nanocrystals (CNCs) on the acid resistance of cementitious composites. CNCs were added to mortar mixtures as additives
【机 构】
：
School of Mining and Petroleum Engineering, University of Alberta, Edmonton, Alberta T6G 2E3, Canada
【出 处】
：
International Journal of Minerals, Metallurgy and Materials
论文部分内容阅读
Acid mine drainage presents an important threat to cementitious structures. This study is aimed at investigating the effect of cellulose nanocrystals (CNCs) on the acid resistance of cementitious composites. CNCs were added to mortar mixtures as additives at cement volume ratios of 0.2vol%, 0.4vol%, 1.0vol%, and 1.5vol%. After 28 d of standard curing, the samples were immersed in a sulfuric acid with a pH value of 2 for 75 d. The unconfined compressive strength (UCS) test, the density, water absorption, void volume test, and thermogravimetric analysis were carried out to investigate the properties of CNC mixtures before sulfuric acid immersion. It was found that the addition of CNC reduced the volume of permeable voids and increased the hydration degree and mechanical strength of the samples. Changes in mass and length were monitored during immersion to evaluate the acid resistance of mixtures. The mixture with 0.4vol% CNC showed a reduced mass change and length change indicating its improved acid resistance.
其他文献
以华北某风电场双馈机组在同步转速下变流器机侧绝缘栅双极型晶体管(insulated gate bipolar transistor,IGBT)频繁失效为案例,通过仿真,研究双馈机组在同步转速点运行特性,分析此特性对变流器可能造成的影响,得出IGBT失效的真实原因为双馈风电机组的同步转速工况下变流器机侧IGBT模块发热较严重,芯片在很小电流情况下便超过耐受温度而失效.给出一种IGBT在同步转速下的最大出力的计算方法,并对比3款常见IGBT在此工况下不同出力.结合工程实际给出适用于变流器的处理方案为降低开关频
针对燃煤发电厂降低大气污染物排放以满足环保要求,以某发电厂5号锅炉改造为例,介绍了实现循环流化床锅炉炉内脱硝、脱硫的原理,并依据该原理对炉内脱硝、脱硫系统提出了改造和优化调整试验方案.调整后的系统,实现了降低锅炉的NOx和SO2的原始排放、提高炉内脱硫和炉内脱硝效率的目的 .
In this work, sodium dicyanamide (SD) was used as a leaching reagent for gold recovery, and the effects of the SD dosage and solu-tion pH on the gold-leaching performance were investigated. A gold recovery of 34.8％ was obtained when SD was used as the sol
The commercial development of lithium–sulfur batteries (Li–S) is severely limited by the shuttle effect of lithium polysulfides (LPSs) and the non-conductivity of sulfur. Herein, porous g-C3N4 nanotubes (PCNNTs) are synthesized via a self-template method
Cobalt (Co)-modified brownmillerite KBiFe2O5 (KBFO; [KBiFe2(1?x)Co2xO5 (x = 0, 0.05)]) polycrystalline is synthesized following the solid-state reaction route. Rietveld refinement of X-ray diffraction data confirmed the phase purity of KBFO and KBiFe1.9Co
To improve the sulfur loading capacity of lithium-sulfur batteries (Li–S batteries) cathode and avoid the inevitable “shuttle effect”, hollow N doped carbon coated CoO/SnO2 (CoO/SnO2@NC) composite has been designed and prepared by a hydrothermal-calcinati
3Y-TZP/3wt％ Al2O3 powder was coated with varying amounts of BN using the urea and borate reaction sintering method, and then multiphase ceramics were prepared by hot pressing sintering. The micro-topography and the compositional analysis of synthesized ce
针对国产200 MW火力发电机组低压缸零功率改造后,因采暖抽汽流量增加26.8％,导致原有加热器换热面积不足,在原位置加热器增容改造后又无法满足切缸调节蒸汽匹配的问题,对“低压缸零功率”配套的热网加热器进行换型增容改造,保证了低压缸零功率改造后供热输出最大,确保了热网系统的安全稳定运行,提高了机组的运行经济性.
An explosion-welded technology was induced to manufacture the GH3535/316H bimetallic plates to provide a more cost-effective structural material for ultrahigh temperature, molten salt thermal storage systems. The microstructure of the bonding interfaces w