【摘 要】
：
Hot deformation behavior of 0.3C-15Cr-1Mo-0.5N high nitrogen martensitic stainless steel (HNMSS) was investigated in the temperature range of 1173-1473 K and at strain rates of 0.001-10 s-1 using a Gleeble 3500 thermal-mechanical simulator.The true stress
【机 构】
：
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of
论文部分内容阅读
Hot deformation behavior of 0.3C-15Cr-1Mo-0.5N high nitrogen martensitic stainless steel (HNMSS) was investigated in the temperature range of 1173-1473 K and at strain rates of 0.001-10 s-1 using a Gleeble 3500 thermal-mechanical simulator.The true stress-strain curves of the studied HNMSS were measured and corrected to eliminate the effect of friction on the flow stress.The relationship between the flow stress and Zener-Hollomon parameter for the studied HNMSS was analyzed in the Arrhenius hyperbolic sine constitutive model by the law of Z =3.76 × 1015 sinh (0.004979σp)7.5022.The processing maps at different strains of the studied HNMSS were plotted,and its flow instability regions in hot working were also confirmed in combination with the microstructure examination.Moreover,the optimal hot deformation parameters of the studied HNMSS could be suggested at T=1303-1423 K and (ε)=5-10 s-1 or T=1273-1473 K and (ε)=0.005-0.04 s-1.
其他文献
Ni-Mo-P coatings are obtained at the surface of ceramic substrate by electroless deposition using palladium as a surface catalyst.The influence of catalyst activation conditions on coatings\' properties was assessed by structural,morphological,electrica
Mg and its alloys are the lightest structural metals available and are extremely attractive for applications as lightweight components,particularly in the automobile,electronic,and aerospace industries.The global market for wrought Mg alloys has steadily
The microstructure,mechanical properties and corrosion behavior of Mg-2Zn-0.6Zr alloy under the as-cast and asextruded conditions were investigated.Microstructure analysis indicated the remarkable grain refinement by extrusion,as well as notable reduction
Machining,especially dry machining of titanium alloys,has been one of the most significant challenges for carbide cutting tools.In this study,aluminum-rich AlTiN coating,as well as TiA1SiN nanocomposite coating,were successfully employed for dry milling o
An M-coated Mg-8 mass％ Li alloy rectangular bar was fabricated by hot extrusion,and then,it was hot-rolled into a thin sheet.The Al coating was uniform in thickness and had good bonding with the substrate during all the processing.This Alcoated Mg-Li allo
A new kind of Mg-2Zn-0.6Ca (wt％) alloy was fabricated by casting and hot extrusion as a high-ductility structural material.The extruded alloy exhibits a superior elongation of ～ 30％,yield strength of 130 MPa and ultimate tensile strength of 280 MPa along
In the electromagnetic induction-controlled automated steel teeming (EICAST) technology of ladle,the height and location of the blocking layer are critical factors to determine the structure size and installation location of induction coil.And,they are al
The corrosion behavior of CoCrFeNiMox alloys was investigated in aqueous environments,NaCl and H2SO4 solutions,respectively,to simulate typical neutral and acidic conditions.The cyclic polarization curves in NaC1 and the potentiodynamic curves in H2SO4 cl
In addition to the advantage of the lightweight of magnesium alloys,magnesium composites have moderate strength and elastic modulus.The proposed application of magnesium composites as diesel truck pistons makes it necessary to assess their wear performanc
Single-pass compression tests were performed to investigate the hot deformation behavior of low-carbon boron microalloyed steel containing three various vanadium contents at 900-1100 ℃ and strain rate of 0.01-10 s-1 using the MMS-300 thermal mechanical si