【摘 要】
：
We demonstrate a diode-pumped femtosecond Yb:CaGdAlO4 (Yb:CALGO) laser with a semiconductor saturable absorber mirror (SESAM) for stable mode-locking operation. A perfect beam profile is measured under 10 W output power with
【机 构】
：
SchoolofPhysicsandOptoelectronicEngineering,XidianUniversity,Xi’an710071,ChinaBeijingNationalLaborat
【出 处】
：
HighPowerLaserScienceandEngineering
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
We demonstrate a diode-pumped femtosecond Yb:CaGdAlO4 (Yb:CALGO) laser with a semiconductor saturable absorber mirror (SESAM) for stable mode-locking operation. A perfect beam profile is measured under 10 W output power with = 1.017 and = 1.016 in the horizontal and vertical directions, respectively. At the repetition rate of 71.66 MHz, the optical pulse duration is 247 fs and the pulse energy is 140 nJ at the central wavelength of 1041 nm, corresponding to a peak power of 0.56 MW. In addition, we also generate continuous wave (CW) power of more than 15 W with TEM00 mode, corresponding to an optical-to-optical efficiency of 44.1%.
其他文献
A simple technique for achieving a stable, room temperature and multi-wavelength lasing with narrow linewidth is demonstrated using Brillouin fiber laser (BFL) with a 100-m-long photonic crystal fiber (PCF) in conjunction with a dual-pass configuration. A
设计一种融入3D打印技术, 实现在高电压、强电磁场环境下检测振动信号的全绝缘多简支梁光纤Bragg光栅振动传感器。通过3D打印机制作而成, 由粘贴于简支梁的光纤Bragg光栅受质量块驱动而产生应变, 通过解调光栅波长变化量实现对振动信号的检测; 有限元分析振动传感器谐振频率为232.47Hz, 应变灵敏度为5.826με·g-1时, 加速度灵敏度为6.991pm·g-1, 表明了传感器理论上的测量带宽及传感器对检测信号的反应程度良好。实验结果表明: 传感器谐振频率为240Hz, 加速度灵敏度为6.270p
目前在微微秒参量分光计中一般采用YAG:Nd3 晶体激光器作为主振荡器，这主要由于微微秒YAG激光器有较高的脉冲重复频率（3~25 Hz),而且辐射的时间参数和能量参数有较高的稳定性。但是YAG:Nd3 晶体的潜力目前几乎已经挖尽。它们的生长工艺持续改善看来也不会使用它制成的激光器的参数有实质性的改善。要得到钕原子份额超过1.2%,在光学上相当完善的大体积YAG:Nd3 晶体的工艺相当复杂。
A single-frequency distributed Bragg reflector (DBR) fiber laser at 1030 nm has been demonstrated using a 0.7 cm long homemade Yb:YAG crystal-derived silica fiber (YCDSF). The absorption and emission cross sections of the YCDSF are
平面光栅上完成的主要试验之一是比较、分解为不同级的由参考平面发出的波前。在小角入射时，由于程差很小，不存在干扰；但当大角入射时，程差能够大于20厘米，甚至更大, 就不能够在整个视场中获得淸楚的条纹。