中共湘潭市雨湖区委2009年经济发展工作报告

来源 :湖南省县域经济发展报告 | 被引量 : 0次 | 上传用户:icewangb
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
一、用中央和省、市委经济工作会议精神统一思想认识在全球金融危机不断加剧、国内外经济环境发生重大变化、党内外迫切需要统一思想认识的关键时刻,中央和省、市委先后召开纪念改革开放30周年和经济工作会议。我们一定要认真学习好、贯彻好、落实好会议精神,把思想和认识统一到科学发展观的要求上来,统一到中央和省、市委对当前经济形势的分析判断上来,统一到各项决策部署上来。30年前,中国共产党召开十一届三中全会,在党和国家面临向何处去的重大历史关头,作出改革开放这一决定当代中国命运的关键抉择,实现了我们党历史上具有深远意义 First, with the central and provincial economic work conference spirit and unify thinking and understanding In the global financial crisis intensified, domestic and international economic environment, major changes, the urgent need to unify the ideological understanding of the party inside and outside the crucial moment, the central and provincial and municipal commissions have held a commemorative reform Opening 30th Anniversary and Economic Working Conference. We must conscientiously study, implement, implement the spirit of the conference, unify our thinking and understanding with the requirements of the scientific concept of development, unify them with the analysis and judgment of the current economic situation by the central, provincial and municipal authorities, and unify them with the decisions and arrangements Up Thirty years ago, the CPC held the Third Plenary Session of the 11th CPC Central Committee, where the party and the country are facing a major historic moment where to go and made the key decision of reform and opening up, which determines the fate of contemporary China, and has achieved far-reaching significance in the history of our party
其他文献
金属涂镀,是一项维修和保护金属零部件的新技术。它能在常温、无槽条件下将零部件恢复到所需尺寸,强化和防护材料表面,延长零部件的使用寿命,应用范围十分广泛。目前这项新
英国伯明翰A.H.Cole有限公司经过10年研究,最近制造出一台新型多级深拉压力机。在压力机一个行程中能完成五次连续拉延工序。采用多级深拉技术特別设计,才制造成功这台压力
重庆汽车发动机厂在一台单柱立式铣床上精铣6140型汽缸体平面时,能够得到凸凹花纹的加工表面,如图1a所示,图中一块块明暗交替的花纹,类似于钳工用手工刮研表面时形成的刮花
热处理工艺过程所需的工夹具,过分强调坚固耐用从节能角度看是不适当的。实践中我们得出:一个合理的工夹具应在保证强度的情况下,重量越轻越好,这样可大幅度减少工夹具本身
薄片零件在热处理后产生翘曲,例如机床中的摩擦片,两个平面平直度要求较高。工件在电磁吸盘的磁力下虽被吸平,磨后卸下工件又翘起来。为此我们曾采用618双酚A环氧树脂粘合剂
一、统一思想,提高认识,切实增强做好明年工作的信心和决心2010年是实施“十一五”规划的最后一年,是应对国际金融危机的关键之年,是国家实施西部大开发战略第二个十年规划的
六年来,Joey每周要抽出时间上两到三节网球课,这对正处于爱玩时期的男孩子无疑是一种挑战,但是,对网球的喜爱战胜了“玩”的冲动。 For six years, Joey spends two to thre
磨损、腐蚀、划伤是机械零件中常见的损伤形式;因加工超差而报废的零件数量也很大;随着进口机械设备的不断增加,配件稀缺,待修复的损伤零件数量也在不断增加;对于中、大型不
在一些中小工厂里,由于设备较少,各热处理工序都在同一电炉内进行,且多为一班生产,因此设备利用率低、热损耗大。我们利用渗碳或淬火后的炉内余热进行锻件的退火、铸钢件消
制完木模后,发现有空洞、凹坑或缺铸造圆角等,可用锯末滴蜡的办法修补。需修补处,先放入锯末,然后滴上蜡液,蜡液很快往锯末里渗透,填满压实即可。修补的地方不软化、不脆裂,