掺Sasobit~的改性沥青与温拌沥青混合料路用性能研究

来源 :公路 | 被引量 : 0次 | 上传用户:a98466
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Sasobit既是一种沥青改性剂又是一种温拌沥青混合料添加剂。在室内,对掺Sasobit添加剂的改性沥青与温拌沥青混合料的路用性能进行了试验研究。结果显示:掺入适量的Sasobit后,沥青胶结料的高温性能、感温性能和低温性能均得到明显的改善;Sasobit温拌沥青混合料的拌和与压实温度比普通热拌沥青混合料降低30℃时,具有与普通热拌沥青混合料相同甚至更好的路用性能,具有明显的经济和社会效益;拌和与压实温度的降低,混合料发生水损害的可能性会增加,建议采用添加抗剥落剂的方法来改善掺Sasobit的温拌沥青混合料的水稳定性。 Sasobit is both a bitumen modifier and a warm mix asphalt additive. In the interior, the road performance of modified asphalt blended with Sasobit additive and warm mix asphalt was tested. The results showed that the high temperature performance, the temperature sensitive property and the low temperature performance of the asphalt binder were obviously improved after the proper amount of Sasobit was added. The mixing and compaction temperature of the Sasobit warm mix asphalt was higher than that of the ordinary hot mix asphalt When the temperature is lower than 30 ℃, it has the same or even better road performance as the ordinary hot mix asphalt mixture, which has obvious economic and social benefits. The lower the mixing and compaction temperature, the more likely the water damage to the mixture will be. Addition of anti-stripping agent to improve the stability of Sasob admixture mixed with warm asphalt mixture.
其他文献
上蒸发器侧板是电冰箱冷冻室中左、右对称的二块侧面板由铝质薄板制成,图1为侧板零件图。其外形为长方形,在二个长边和一个短边以及与它们相连接的圆角,均有窄槽边沿,槽宽仅
A3-07ACT引线框全拼块级进模16脚硬质合金精密引线框架级进模插头簧片多工位级进模W121接触簧片级进模 A3-07ACT lead frame full block progressive die 16-pin carbide p
《联系词与连接词:述谓关系、谓语倒装及系词的句法分析》(Relators and Linkers:TheSyntax ofPredication,Predicate Inversion,and Copulas)2006年由麻省理工学院出版社出
为了研究桩土相互作用下大跨度钢拱桥的地震反应特点以及塑性铰的形成部位和发展过程,利用ANSYS有限元程序对比研究了在多组地震输入条件下,考虑基础固结和桩土相互作用下的
在开始中坚持50米的泳道上,留下长长的坚持。这是耐力的考验,每一次向前,都充满执著和坚定。蓝色的泳道前,随着裁判员做出预备的指令后,运动员们站在出发台上,做好了准备,各
产品的商标对于企业打开产品的销路进入市场有着举足轻重的作用。而商标通常被赋予文化的涵义。因此商标的成功翻译和命名对于消费者选择产品有着重要的影响。文章对商标和文
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
《机械工人》(热加工)1989年第2期上刊登了我所“ST-11电弧刨割条”的文章后,我们经常收到一些读者的来信,询问ST-11电弧刨割条在使用中的一些问题及使用后的信息反馈意见,
氧丙烷及数控切割技术推广会于1993年7月16月至20日在北戴河召开。会议由中国焊接协会、中国机械工程学会焊接分会、机械工业部哈尔滨焊接研究所、机械工业部火焰切割机具质
在GB3177—82中,工件的形状误差通常是依靠加工过程的精度来控制的;工件合格与否,只按一次测量来判断;对于温度、湿度以及计量器具和标准器具的系统误差均不进行修正。为此,