论文部分内容阅读
红外2013年第34卷第12期 目录
【出 处】
：
红外
【发表日期】
：
2013年34期
其他文献
A high-efficiency hybrid Brillouin/ytterbium fiber laser (BYFL) is demonstrated using a 41.5-cm-long highly ytterbium-doped fiber and a 10-m-long single-mode optical fiber. The BYFL operates at 1 052.92 nm, and the difference between it and the Brillouin
An optical bandwidth analysis of a quantum-well (16 nm) transistor laser with 150-\mum cavity length using a charge control model is reported in order to modify the quantum-well location through the base region. At constant bias current, the simulation s
A temperature-compensated fiber optic Fabry-Perot accelerometer (FOFPA) formed by symmetrically bonding an all-silica in-line fiber Fabry-Perot etalon (ILFFPE) and a piezoelectric ceramic unimorph actuator (PCUA) to two surfaces of a silica cantilever is
In this letter, we investigate the structural, optical, and electrical properties of Al-doped ZnO (AZO) thin film coating prepared by direct current (DC) facing-target sputtering method at room temperature, of which the average optical transmittance is 81
非球面光学元件在光学系统中的应用越来越广泛，为了提高光学系统能量收集能力，高陡度非球面光学元件常常被采用。然而，高陡度非球面光学元件的光学加工至今仍是光学制造领域内的难题之一。通过一块F数0.42的大偏离量离轴碳化硅非球面反射镜的制造实例，详细地介绍了一些重要的技术研究进展。首先是离轴非球面直接铣磨技术，与传统的铣磨最接近球面相比残余误差大大减小，估算后续光学研磨的加工周期与原来相比可以缩短2/3左右；通过对非球面方程坐标变换，大大减小了矢高差，使数控加工难度极大降低，而通过磨头沿非球面法线方向数控加工可
同时实现大视场、高分辨率成像是光学显微技术发展至今不断追求的永恒目标。传统光学显微镜由于其光学设计原理限制,空间带宽积一般总是限制在百万像素量级,从而无法同时兼顾高分辨率与大视场。另一方面,复杂的光学系统也使显微镜变得日趋昂贵、笨重、复杂且难以维护,极大地限制了其推广和应用。无透镜片上显微成像技术是近年来发展出的一种新概念计算成像技术:其不利用成像透镜聚焦,而直接将所观测的样本紧贴于成像器件光敏面
We discuss the feasibility of realizing a cold atom space clock with counter-propagating cold atoms in microgravity. The design of the space clock is based on an atomic beam clock with Ramsey cavity, except that magneto-optical trap (MOT) is placed at eac
针对红外超光谱干涉光谱仪的技术特点,分析其探测器非线性响应的形成机理,仿真含有高阶非线性误差的干涉数据,并研究二、三阶非线性响应对光谱的影响;提出一种迭代方法,即通过交叉迭代使光谱带外畸变最小,从而确定校正系数进而校正非线性响应;通过获取不同温度黑体观测的干涉数据,用交叉迭代法校正实测数据并复原光谱,将未吸收波数光谱响应与黑体辐亮度进行拟合。结果表明:二阶非线性响应主要影响带外数据,三阶非线性响应