锅炉引风机叶轮粘灰原因与应急处理

来源 :设备管理&维修 | 被引量 : 0次 | 上传用户:zhaoyu_hit
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
引风机叶轮粘灰的来源是燃煤锅炉烟气中的飞灰,烟气中飞灰含量较高时,容易在叶轮上结灰。粘灰也与目前流行的湿式除渣、除尘方式有关,还与频繁压火停炉有直接关系。压火时,由于烟囱的抽吸作用,炉膛及烟道内仍有气流流动,使炉膛内的湿蒸汽经风机叶轮而凝结粘灰,且粘灰的不均匀程度明显高于其它情况,更易引起风机的振动。 Induction fan impeller sticky ash is the source of fly ash in coal-fired boiler flue gas, high fly ash content in the flue gas, easy to ash on the impeller. The sticky ash is also related to the prevailing wet slag removal and dust removal methods, and it is also directly related to frequent fire suppression and shutdown. During the fire, due to the suction effect of the chimney, there is still air flow in the furnace and the flue, so that the wet steam in the furnace condenses and sticks ash through the fan impeller, and the unevenness of the viscous ash is obviously higher than other conditions, The vibration.
其他文献
Background:Coronal diffusion-weighted magnetic resonance imaging (DW-MRI) and apparent diffusion coefficient (ADC) values have gradually become applied (followi
数控机床上的光栅尺是应用非常广泛的位置测量反馈元件。光栅尺是一种很精密的元件,其维护一般仅限于外部尺身的擦拭,不要轻易拆卸,更不能随便将其拆开。经过长期使用,密封条老化弹性变差,车间空气中的油雾、尘埃可能会进入尺内,甚至由于密封、防护不严,冷却液可能会直接进入尺内造成故障。被油或冷却液污染是光栅尺常见的故障,处理的方法是将其拆开进行清洗。
粉碎机主要由电动机、偏心重块、振动平台、振动弹簧及底座等机构组成。工作时,电动机带动偏心重块旋转,在离心力的作用下,产生激振力,使振动平台上的物料罐产生振动,在物料
我厂用X52K型立铣加工汽车配件轴上的3个半圆键,要求同一轴截面的对称度同时达到0.04~0.08mm.长期以来,产品对称度超差,严重时误差达到0.20~0.30mm.过去总是更换主轴轴承,但轴
本文通过对荣华二采区10
期刊
我公司一台φ2.2m×1.3m水泥磨,在1993年5月由于油泵电机传动轴键滚切,致使磨机球面瓦缺油导致巴氏合金瓦表面烧熔,被迫停机.若更换新瓦,不仅影响生产,时间长,而且经济损失较
我厂1983年扩建建造了两座6500t冷库,在制冷冷却系统中,由于没有完善的水处理设备,供水系统结垢情况越来越严重,影响生产的情况也逐渐地突出,而且清洗除垢的费用每次上万元
旋转扒杆是一种用于油田钻机塔形井架安装的辅助设备.这种钻杆的材质是铬钼合金钢,在正常条件下,难以进行焊接.为此,我们从加工工艺上进行了改进.