【摘 要】
：
We demonstrate high-brightness blue organic light emitting diodes (OLEDs) using two types of guest-host systems. A series of blue OLEDs were fabricated using three organic emitters of dibenz anthracene (perylene), di(4-fluorophenyl) amino-di (styryl) biph
【机 构】
：
SchoolofMaterialsScienceandEngineering,ShanghaiUniversity,Shanghai200072,ChinaLangfangPolytechnicIns
【出 处】
：
OptoelectronicsLetters
论文部分内容阅读
We demonstrate high-brightness blue organic light emitting diodes (OLEDs) using two types of guest-host systems. A series of blue OLEDs were fabricated using three organic emitters of dibenz anthracene (perylene), di(4-fluorophenyl) amino-di (styryl) biphenyl (DSB) and 4,4'-bis[2-(9-ethyl-3-carbazolyl)vinyl]biphenyl (BCzVBi) doped into two hosting materials of 4,4'-bis(9-carbazolyl) biphenyl (CBP) and 2-(4-biphenylyl)-5(4-tert-butyl-phenyl)-1,3,4-oxadiazole (PBD) as blue emitting layers, respectively. We achieve three kinds of devices with colors of deep-blue, pure-blue and sky-blue with the Commission Internationale de L'Eclairage (CIE) coordinates of (0.16, 0.10), (0.15, 0.15) and (0.17, 0.24), respectively, by employing PBD as host material. In addition, we present a microcavity device using the PBD guest-host system and achieve high-purity blue devices with narrowed spectrum.
其他文献
本文研究了C轴YLF晶体的光谱性质,并利用这种新型激光晶体,进行了主动锁模,被动锁模和主被动锁模实验.C轴YLF激光器直接发射1.053μm激光,锁模脉冲序列能量起伏小于±4%,脉宽起伏不大于±10%.
A new approach for an all-fiber coherent beam combining by active phasing a fiber combiner is presented, and effect of fill factor of the fiber combiner on the all-fiber coherent combining is also numerical analyzed. Experimental results show that the pow
基于角谱衍射理论，对扫描积分塔尔博特光刻术进行了理论分析与数值模拟。研究了扫描距离、扫描起始位置、扫描速度非匀速以及照明光源不同特性对扫描积分塔尔博特光刻所得光栅条纹质量的影响。模拟结果表明，当扫描距离为塔尔博特周期的整数倍时，扫描起始位置、扫描速度的非匀速性对扫描积分塔尔博特光刻的成像质量影响较小；当入射光源存在一定谱宽或发散角不大于0.05°时，扫描积分塔尔博特光刻仍可得到对比度较一致的倍频光栅条纹，证实了扫描积分塔尔博特光刻具有良好的工艺适用性。扫描积分塔尔博特光刻不需要昂贵而复杂的投影光学系统，可
为了控制激光熔覆成形薄壁金属制件的精度，分析了激光熔覆成形金属薄壁的工艺理论和影响因素。采用BP神经网络建立了激光功率、光斑直径、扫描速度和送粉率与金属零件壁厚的非线形关系模型和激光熔覆成形薄壁制件的精度控制系统。通过优化神经网络的权值和阈值，并引入动量因子和学习速率的自适应调整，克服了BP算法容易陷入局部最小值的问题。用实验参数作为训练样本对模型进行训练，并进行了误差分析。实验和仿真结果表明，训练样本和检验样本的最大相对误差分别为1.93％和1.19％，预测精度高。该网络模型可用于优化激光熔覆成形工艺参
使氟化氪准分子激光器的248毫微米输出转换为七次谐波,得到波长为35.5毫微米的可调相干辐射。在激光焦点和脉冲超音速氦气流的相交处发生非线性相互作用。在氦、氙气流中，可得到三次和五次谐波，产生83毫微米和50毫微米的相干输出。