【摘 要】
：
We propose a novel in-band optical signal-to-noise ratio (OSNR) monitoring method based on polarization interference. The method realizes a monitoring accuracy of ±0.5 dB within the range of 9–34 dB. Our results indicate that the proposed method is transp
【出 处】
：
ChineseOpticsLetters
论文部分内容阅读
We propose a novel in-band optical signal-to-noise ratio (OSNR) monitoring method based on polarization interference. The method realizes a monitoring accuracy of ±0.5 dB within the range of 9–34 dB. Our results indicate that the proposed method is transparent to bitrate and modulation format, as well as independent of polarization mode dispersion and chromatic dispersion.
其他文献
为研究食用靛蓝的降解过程,使用紫外-可见吸收光谱法建立食用靛蓝的光降解率模型。食用靛蓝吸收光谱中611 nm处的吸光度随光照时间增加而递减,光照8 h后,611 nm处的吸光度接近于0。基于不同浓度食用靛蓝的吸收光谱,通过指数拟合分别建立了食用靛蓝在611 nm处的吸光度-质量浓度预测模型和500~700 nm范围内吸收峰面积-质量浓度预测模型。结果表明:吸收峰面积-质量浓度预测模型的效果更好;将完全降解后的食用靛蓝溶液作为干扰物,与新配制的食用靛蓝溶液混合来验证吸收峰面积-质量浓度预测模型的适用性,模型
A fiber-optic relative-humidity (RH) sensor composed of multilayer of porous dielectric films is proposed. The transducer deposited on fiber end-face is multilayer coating consisting of nano-porous TiO2 and SiO2 films, which forms a low-fineness Fabry-Per
全光信号处理是高速光通信网络的一个关键技术。光头识别作为实现全光分组交换的关键技术之一，通过使用全光比较器可以实现。提出基于半导体光放大器马赫曾德尔干涉仪(SOA-MZI)级联结构的全光3 bit比较器，通过数值模拟对其进行了仿真研究，仿真速率为10 Gb/s。模拟结果显示输出信号质量良好，峰值功率超过7 mW，消光比为48 dB，脉冲半峰全宽为(FWHM)8.5 ps。输出脉冲具有较高的强度和稳定性。
We demonstrate a high responsivity all-silicon in-line optical power monitor by using the thermal effect to enhance the quantum efficiency of defect-mediated absorption at 1550 nm. The doping compensation technique is utilized to increase the density of l
The precise alignment of a high-performance telescope is a key factor to ensure the imaging quality. However, for telescopes with a wide field of view, the images are sometimes under-sampled. To study the effects of under-sampled images on the precision o
A large-mode-area (LMA) ytterbium-doped photonic crystal fiber (PCF) with core NA of 0.034 and core diameter of 50 μm was made by the stack-and-draw technique. The core is formed by Yb3 /Al3 /F /P5 co-doped sil
1981年6月中旬，我们受科学院和上海光机所的派遣，接受苏联科学院通讯院士西伯利亚自动化与电测所所长、全苏第七届瓦维洛夫非线性光学会议主席的邀请,参加了这届会议，会议的地点在新西伯利亚科学城。
对表面已进行喷砂处理的增材制造TC4钛合金在氩气环境下进行激光抛光实验,通过极化曲线测试研究了抛光前、后钛合金的耐蚀性,并结合表面粗糙度、晶粒尺寸、表面残余应力以及显微组织分析了激光抛光对TC4钛合金耐蚀性的影响。研究结果表明:抛光钛合金的自腐蚀电位与自腐蚀电流密度均大于未抛光钛合金,说明抛光钛合金相比于原始钛合金的被腐蚀倾向更小,但其一旦受到腐蚀,腐蚀速率会略大于原始钛合金。自腐蚀电位的升高源于钛合金表面粗糙度的降低,自腐蚀电流密度的增大则是因为表面晶粒的细化以及残余拉应力的存在。