Optimum design and preliminary experiments of a novel parallel end traction apparatus for upper-limb

来源 :机械工程前沿 | 被引量 : 0次 | 上传用户:eastliu33
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Robot-assisted technology has been increasingly employed in the therapy of post stroke patients to deliver high-quality treatment and alleviate therapists\' burden.This paper introduces a novel parallel end traction apparatus (PETA) to supplement equipment selection.Considering the appearance and performance of the PETA,two types of special five-bar linkage mechanisms are selected as the potential configurations of the actuation execution unit because of their compact arrangement and parallel structure.Kinematic analysis of each mechanism,i.e.,position solutions and Jacobian matrix,is carried out.Subsequently,a comparative study between the two mechanisms is conducted.In the established source of nondimensional parameter synthesis,the singularity,maximum continuous workspace,and performance variation trends are analyzed.Based on the evaluation results,the final scheme with determined configuration and corresponding near-optimized non-dimensional parameters is obtained.Then,a prototype is constructed.By adding a lockable translational degree of freedom in the vertical direction,the PETA can provide 2D planar exercise and 3D spatial exercise.Finally,a control system is developed for passive exercise mode based on the derived inverse position solution,and preliminary experiments are performed to verify the applicability of the PETA.
其他文献
Three different structural engineering designs were investigated to determine optimum design variables,and then to estimate design parameters and the main objective function of designs directly,speedily,and effectively.Two different optimization operation
The ultra-high-performance concrete (UHPC) and fiber-reinforced polymer (FRP) are well-accepted high-performance materials in the field of civil engineering.The combination of these advanced materials could contribute to improvement of structural performa
The objective of this paper is to quantify the variability in emissions of off-road equipment using a portable emission measurement system.A total of 53 commonly used equipment for agriculture,base construction,paving construction,and material handling we
The problem related to bearing capacity of footing either on pure soil or on pure rock mass has been investigated over the years.Currently,no study deals with the bearing capacity of strip footing on a cohesive soil layer overlying rock mass.Therefore,by
A methodology to compute the CO2 uptake of recycled aggregate concrete is proposed in the commented paper.Besides some typos in several formulas,it is found that the approach to estimate the specific surface area of the recycled aggregates is not correct.
期刊
采用失重法、电化学法及表面分析测试研究了农林废弃物核桃青皮提取物(WGHE)与阴离子表面活性剂十二烷基磺酸钠(SLS)对冷轧钢在2.0 mol/L H3PO4介质中的缓蚀协同效应,并对WGHE中的缓蚀有效成分进行了探究.结果 表明:单独的WGHE、SLS具有中等程度的缓蚀性能,50℃时100 mg/L的缓蚀率仅为50%左右;WGHE/SLS复配后缓蚀率不断上升,最高缓蚀率可达95.3%,两者之间存在显著的缓蚀协同效应,缓蚀协同效应系数随温度的升高而增大.WGHE/SLS复配缓蚀剂更能同时有效抑制阴极和阳极
This paper proposes a new Deep Feed-forward Neural Network (DFNN) approach for damage detection in functionally graded carbon nanotube-reinforced composite (FG-CNTRC) plates.In the proposed approach,the DFNN model is developed based on a data set containi
In waterfront geotechnical engineering,seismic and drainage conditions must be considered in the design of retaining structures.This paper proposes a general analytical method to evaluate the seismic active earth pressure on a retaining wall with backfill
探究了CO2湿气环境中P110SS抗硫钢在不同温湿度下的S腐蚀特征及腐蚀机理.采用X射线光电子能谱(XPS)和扫描电子显微镜(SEM),对P110SS钢表面腐蚀产物膜的化学组成、微观形貌及厚度及去除腐蚀产物后基体的微观形貌进行了表征.结果 表明:在60℃、相对湿度为30%的条件下,S不会参与腐蚀反应,但腐蚀环境中的Cl和CO2会导致抗硫钢发生局部腐蚀;当相对湿度升高至60%和90%时,S参与了腐蚀的阴极反应,生成FeS,并导致抗硫钢发生全面腐蚀.在80℃、相对湿度为30%的条件下,S也参与腐蚀的阴极反应,
The demand for redundant hydraulic manipulators that can implement complex heavy-duty tasks in unstructured areas is increasing;however,current manipulator layouts that remarkably differ from human arms make intuitive kinematic operation challenging to ac