论文部分内容阅读
In order to study the effects of aging treatment on the intergranular corrosion(IGC)and stress corrosion cracking(SCC)of 7003 aluminum alloy(AA7003),the intergranular corrosion test,electrochemical test and slow strain rate test(SSRT),combined with optical microscopy(OM)and scanning electron microscopy(SEM)as well as transmission electron microscopy(TEM)observations have been carried out.The IGC and electrochemical test results showed that the IGC resistance of AA7003 for peak aged(PA)temper is the lowest,with double peak aged(DPA)the moderate,and retrogression and re-aging(RRA)the highest among three tempers,which is attributed to the continuous feature of precipitation on grain boundary of PA temper and the interrupted feature of precipitation on grain boundary of DPA and RRA tempers,as well as the wide precipitation free zones(PFZ)of RRA temper.In addition,the SSRT results indicated that all three tempers AA7003 are susceptible to SCC in IGC solution,and the change tendency of SCC susceptibility(I SCC)of AA7003 for three tempers follows the order:I SCC(RRA)
其他文献
Four Nb-Ti microalloyed steels were refined and rolled to study the composition optimization of Nb-Ti microalloyed steels.The effects of Nb and Ti on the microstructures,precipitates and properties of Nb-Ti microalloyed steel were investigated.The results
Effect of Graphene Surface Functional Groups on the Mec-hanical Property of PMMA Microcellular Compo
The functional groups on graphene sheets surface affect their dispersion and interfacial adhesion in polymer matrix. We compared the mechanical property of polymethymethacrylate (PMMA) microcellular foams reinforced with graphene oxide (GO) and reduced gr
The damage mechanism and energy dissipation of the Polyethylene (PE) laminates in impacting was investigated. It was found that the dissipated energy of the impacting sphere bullet by the 1-mm-thick PE plate firstly increased with the impacting velocity i
In order to examine the effect of extrusion ratio on the microstructure and mechanical behavior in Al-Cu-Mg-Ag alloy, the Al-6.3Cu-0.48Mg-0.4Ag alloy was subjected to extruding with different extrusion ratios of 17, 30 and 67. The results indicate that th
Banana pseudo-stem was liquefied in the mixture of polyhydric alcohols of polyethylene glycol (PEG400) and glycerol. Hydroxyl value of liquefied products ranged from 294.8 to 370.2 mg KOH/g and Mn was about 430. Liquefied products (LBPP) could be used as
The dynamic load characteristics of a proton exchange membrane fuel cell (PEMFC) with a dead-ended anode were studied. In a 70 h experiment, the effects of anode pressure, operating temperature, and relative humidity of the cathode on the performances of
Properties of Steel Slag and Stainless Steel Slag as Cement Replacement Materials: A Comparative Stu
To enhance the understanding about the utilization of steel slags as a cementitious material, we comparatively studied the chemical, mineralogical and morphological properties of two types of steel slag; basic-oxygen-furnace carbon slag (BOF C) and electr
In order to distinguish the filling effect and volcanic activity and explore the ways motivating the activity of rich-silicon iron ore tailing(IOT),inert quartz was brought in as the correction standard,the influences of fineness,calcination,thermal curin
The SO42-concentration distributions in surface region of cement mortar immersed in sulfate solution at early stage were measured by layered sampling method combined with chemical analysis,and the diffusion coefficients of SO42-anions in surface region of
A conjugated polymer of poly(4,4\'-bis(thien-2-yl)azobenzene-co-3-hexylthiophene) (PTAB-H), bearing azo group in main chain and soluble in THF, chloroform, was synthesized through FeCl3 oxidation copolymerization with 3-hexylthiophene, and the monomer o