Characterization of a Lacustrine Shale Reservoir and the Evolution of its Nanopores: A Case Study of

来源 :地质学报(英文版) | 被引量 : 0次 | 上传用户:aglusaiy
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
The Songliao Basin is one of the most important petroliferous basins in north China.With a recent gradual decline in conventional oil production in the basin,the exploration and development of unconventional resources arc becoming increasingly urgent.The Qingshankou Formation consists of typical Upper Cretaceous continental strata,and represents a promising and practical replacement resource for shale oil in the Songliao Basin.Previous studies have shown that low-mature to mature Qingshankou shale mainly preserves type Ⅰ and type Ⅱ1 organic matter,with relatively high total organic carbon (TOC) content.It is estimated that there is a great potential to explore for shale oil resources in the Qingshankou Formation in this basin.However,not enough systematic research has been conducted on pore characteristics and their main controlling factors in this lacustrine shale reservoir.In this study,19 Qingshankou shales from two wells drilled in the study area were tested and analyzed for mineral composition,pore distribution and feature evolution using X-ray diffraction (XRD),scanning electron microscopy (SEM),low-pressure nitrogen gas adsorption (N2-GA),and thermal simulation experiments.The XRD results show that clay,quartz,and feldspar are the dominant mineral constituents of Qingshankou shale.The clay minerals are mostly illite/smectite mixed layers with a mean content of 83.5%,followed by illite,chlorite,and kaolinite.There are abundant deposits of clay-rich shale in the Qingshankou Formation in the study area,within which many mineral and organic matter pores were observed using SEM.Mineral pores contribute the most to shale porosity;specifically,day mineral pores and carbonate pores comprise most of the mineral pores in the shale.Among the three types of organic matter pores,type B is more dominant the other two.Pores with diameters greater than 10 nm supply the main pore volume;most are half-open slits and wedge-shaped pores.The total pore volume had no obvious linear relationship with TOC content,but had some degree of positive correlation with the content of quartz + feldspar and clay minerals respectively.However,it was negatively correlated with carbonate mineral content.The specific surface area of the pores is negatively related to TOC content,average pore diameter,and carbonate mineral content.Moreover,it had a somewhat positive correlation with clay mineral content and no clear linear relationship with the content of quartz + feldspar.With increases in maturity,there was also an increase in the number of carbonate mineral dissolution pores and organic matter pores,average pore diameter,and pore volume,whereas there was a decrease in specific surface area of the pores.Generally,the Qingshankou shale is at a low-mature to mature stage with a TOC content of more than 1.0%,and could be as thick as 250 m in the study area.Pores with diameters of more than 10 nm are well-developed in the shale.This research illustrates that there are favorable conditions for shale oil occurrence and enrichment in the Qingshankou shale in the study area.
其他文献
该文讨论了基于CIE-1976年LAB均匀颜色空间的滤色处理算法,分析了双面提花、单 胖以及双胖针织物的数学模型.并在此基础上以Visual Basic 5.0和MS-Access 97为开发工具开发了
聚酯/聚酰胺(PET/PA6)双组份纺粘水刺非织造布由于具有强力高、透气性好、手感柔软等优异性能而在高级擦拭布领域得到广泛应用,但其亲水及亲油性能有限。本文研究了PET/PA6双
城市市政园林绿化工程在净化城市空气、改善城市环境方面发挥着非常重要的作用.然而从当下城市市政园林绿化工程项目质量管理发展现状来看,依然存在一些问题,严重影响最终项
学位
该课题首次将时间序列理论应用于纺纱张力的控制.首先利用一套数据采集系统采集纺纱张力,然后将数据进行零化处理后利用计算机生成合适的AR模型,对交流电机进行控制,从而控制
该课题的目的是开发一种用于多梳经纺织物生产的计算机辅助花型设计系统.论文详细介绍了多梳经纺织物CAD系统的设计和开发方法.首先,分析了多梳经纺织物的形成原理 和结构特
第Ⅰ卷(单项选择题,共44分) rn乍得湖位于非洲中北部,地处撒哈拉沙漠南缘,湖面海拔281米,平均深度1.5米.乍得湖属于内流湖,水位常随季节变化,湖泊面积变化也很大,但湖水盐度
期刊
该文主要从三个方面对Tencel纤维的性能进行分析,一是纤维的纺纱工艺;二是Tencel纤维纯纺及混纺线性能测试和结构分析;三是Tencel纤维针织物的性能探讨.Tencel纤维是一种优良
该课题主要进行了如下的研究工作,得到以下的研究结果:(一)束强测试分析色条束强染色损伤.(二)电镜实验分析羊毛纤维表面结构染色损伤.
目前,电火花加工是难加工材料加工的一种主要方法,但是其加工能量受制于脉冲电源,蚀除效率很低。电火花诱导烧蚀是一种新出现的针对难加工材料加工的方法,利用电火花诱导工件活化