Oil-based nanofluids including 0.75%—1.75%(mass fraction) carbon nanotubes(CNTs) without any surfactants have been synt......

Computer aided design of heat treatment for AISI P20 mold steel with good machinability is attempted to proceed by the c......

White layers in hard turned surfaces were identified and measured as a function of turning parameters based on the Taguc......

An experimental investigation is carried out to machine SiC ceramic material through the method of high speed plane lapp......

Near net-shape production of complex parts with higher mechanical properties is one of the most important final goals of......

研究了LM25Al/SiCp复合材料的铣削加工特征。将获得的相关试验数据采用响应面方法建立了一个数学模型来描述各种加工参数对后刀面......

The tools discussed in this paper include fixtures, jigs and gages,which are indispensable in any type of manufacture on......

Ultra-precision machining is an effective approach to achieve high dimension accuracy and surface finish required in opt......

Laser consolidation(LC) is a novel computer-aided manufacturing process developed by the Industrial Materials Institute ......

In order to obtain a high output energy from a xenon lamp-pumped solid-state dye laser, homogeneities of laser mediums a......

This paper presents a transimpedance amplifier(TIA) capacitance detection circuit aimed at detecting micro-capacitance, ......

The cutting performance of particle reinforced meta ll ic matrix composites (PRMMCs) SiC p/Al in ultrasonic vibration c......

A new idea for designing wheel patterns is presented so as to solve the problems about machining accuracy ofworkpiece a......

The methodology of 5-axis cutter selection to avert collision for free-form surface machining by flat-end cutters is pre......

This paper describes the design and fabrication of a range of ‘gas cell’ microtargets produced by the Target Fabricati......

AZ80 magnesium alloy was prepared by hot extrusion of recycled machined chips and its microstructure and mechanical prop......

A potassium dihydrogen phosphate(KDP) optical crystal was machined to an ultra-precision surface with water-in-oil(W/O) ......

We have developed high damage threshold filters to modify the spatial profile of a high energy laser beam. The filters a......

The squeeze casting of a 2024 Al alloy was carried out to investigate the effect on microsegregation in the alloy of th......

Based on the Canadian Standards Association (CSA) criteria,105 pullout specimens were tested to investigate the effect o......

To understand the deformation and removal mechanism of material on nano-scale at ultralow loads,a systemic study on AFM ......

Superplastic tensile tests of AINp/6061 Al Compostics, fabricated by powder metallurgy techniques, were performed st st......

The present work is focused on optimization of machining characteristics of AI/SiCp composites. The machining characteri......

Aluminum based metal matrix composites are offering o utstanding properties in a number of automotive and aircraft comp......

This study aimed to evaluate the surface roughness and wetting properties of various dental prosthetic materials after d......

Experiments were conducted to investigate the characteristics of the flow boiling critical heat flux (CHF) and transiti......

A new type of high-frequency micro-pump was designed, in which GMA (Giant Magnetostrictive Actuator) was employed to rep......

The atomic force microscopy (AFM)-based nanomachining of nanochannels on silicon oxide surfaces is investigated both the......

3D evaluation method of cutting surface topography for C/Ph composites was established.The cutting surface was measured ......

Hybrid metal matrix composites consist of at least three constituents-a metal or an alloy matrix and two reinforcements ......

In this study, liquid nitrogen was applied to grind Si Cp/Al composites with high volume fraction and large Si C particl......

A novel powder metallurgy (P/M) material with high wear resistance is developed in orderto decrease the wear and lubrica......

An attempt was made to investigate the machinability of Si Cp/Al composites based on the experimental study using mill-g......

In the present work, the wire electrical discharge machining(WEDM) process of the 65 vol% SiCp/2024 Al composite prepare......

This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It co......

Microchannel heat sinks constitute an innovative cooling technology for the removal of a large amount of heat from a sma......

The passive residual heat removal exchanger (PRHR HX),which is a key equipment of the passive residual heat removal syst......

Issues in industrialization of RFPE (Reference Free Part Encapsulation) are discussed in this paper. The issues are ass......

A cyclic plasticity model is used into finite element (FE) method to obtain the details of elastic-plastic stress-strain......

A new method is proposed to suppress chatter, in which the ultrasonic elliptical vibration is added on the cutting tool ......

Robotic milling is a developing method for rapidly producing prototypes and parts, but the application is limited for ma......

The change of conductivity, thickness and scanning electron microscopy (SEM) appearance of the anode film of CrWMn in 10......

The continuing miniaturization of electronic devices in microelectronics and semiconductors drives the development of ne......

Better understanding of variations in the mechanical properties of cancer cells could help to provide novel solutions fo......

Some observation relating to the solubility, diffusivity and intergranular cracking by hydrogen transport from the exter......

The middle convex and varying ellipse piston is th e key component of an internal combustion engine In general,the p......

Many nanocrystallized areas have been found with transmission electron microscope (TEM) in a Cr-Mn-N austenitic stainles......

本文通过实验研究，证明导电加热切削这一非传统切削方法能够改善工件性能，有效抑制积屑瘤、鳞刺和颤振，是低这切削时改善工件表面质量......

The present study aims at developing the high speed steel (HSS) as roll materials to replace the traditional roll mater......

By introducing the Zener-Hollomon parameter, which synthetically considers the influence of deformation temperature and......