大尺寸Nano-SiCp/AZ91D镁基复合材料的组织及其力学性能

来源 :The 11th China-Japan joint conference on Composite Materials | 被引量 : 0次 | 上传用户：sunvoo

【摘要】

：

采用超声波辅助搅拌铸造的方法，制备了体积分数为1％的纳米SiCp/AZ91D镁基复合材料的大尺寸铸锭。对其不同部位的组织进行观察发现，大尺寸铸锭外侧纳米颗粒分布相对内侧更为均匀，并且，不同部位的晶粒尺寸存在显著差异，铸态复合材料外侧上部晶粒相对内侧下部晶粒更为细小。复合材料不同位置颗粒分稚情况存在较大差异，部分位置可以观察到明显的团聚现象。力学性能测试结果表明：铸态复合材料外侧中部的力学性能最优，

【作者】

：

王晓军吴昆

【机构】

：

哈尔滨工业大学材料科学与工程学院,哈尔滨150001

【出处】

：

The 11th China-Japan joint conference on Composite Materials

【发表日期】

：

2014年3期

【关键词】

：

大尺寸铸锭纳米SiCp 镁基复合材料颗粒分布

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

其他文献

Tensile Properties and Aging Behaviors of 6061Aluminum Alloy Composites Reinforced with In-situ MgAI

In-situ generated MgAl2O4 nanowhiskers reinforced 6061 aluminum (Al) alloy composites have been successfudly synthesized by reaction hot pressing under a relatively low temperature (600 ℃).

会议

metal matrix composites (MMCs)MgAl204 nanowhiskerin-situ synthesishot extrusi

单轴力多约束条件下复合材料单向加筋壁板结构效率分析方法的研究

通过建立复合材料单向加筋壁板单元的基本力学假设和计算分析模型，提出了一种综合分析其结构力学性能和多约束条件下进行快速优化分析的方法，并利用该方法对典型的复合材料单向加筋壁板结构进行了结构效率分析和优化，得到了其结构效率随各设计参数的变化趋势和相对最优结构参数，为复合材料单向加筋板的设计提供直接参考。本文方法综合考虑筋条总体稳定性、局部稳定性、结构静强度约束及其之间相互影响，并在基本假设的基础上将复

会议

复合材料结构优化单向加筋壁板结构效率总体稳定性

ULTRASONIC WELD BETWEEN AMORPHOUS AND CRYSTALLINE POLYMER WITH INSERITING INTERPOSED MATERIAL

Ultrasonic welds between crystalline and anmorphous polymers of PMMA-PLA and PMMA-POM are carried out,especially for the immiscible materials pair of PMMA-POM.Both of the effects of welding conditions

会议

Crystalline polymerAmorphous polymerUltrasonic weld

Microwave Tunable Properties of Polymer Composites Containing Ferromagnetic Microwires

In the context of developing multi-functional composites [1],our efforts have been devoted in exploring ideal functional fillers that could meet the criteria: (i) a likely omnipotent functional filler

会议

Improvement of the CNT Twisted Yarn Using Cardo Epoxy Resin

CNT yarn is made from CNT bundles.But it is so low in tensile strength for the weak Van der Waals force of CNT each other.Therefore we aimed at the strength improvement of CNT yarn by impregnation of

会议

Carbon nanotube spun yarnCardo structureWeibull distributionBonding energy

Nanoscale Mass Sensor Based on the Vibration of Carbon Nanotube - Theoretical analysis of vibration

Carbon nanotubes (CNTs) are nanomaterials with extremely favorable mass sensor properties.In this paper,we proposed that CNTs under the clamped boundary condition and an axial tensile load were consid

会议

NanotubesSensorVibrationSimulation

Mechanical Properties of Untwisted Carbon Nanotube Yarn with Densification Treatment

CNT yarn is expected to be a good method for utilization of CNTs which have extremely high mechanical properties.In this study,we fabricate untwisted CNT yarn by drawing CNTs from vertically aligned C

会议

Untwisted CNT yarnPolymer treatmentTensile properties Unidirectional composite

Innovation of Polymer Based Functionally Graded Materials (FGMs)

Functionally graded multiwaIled carbon nanotube (MWCNT) reinforced epoxy matrix composites (FGMs) were innovated by using the centrifugal method;the aggregation of MWCNTs that occurred during the epox

会议

Functionally graded materials (FGMs)microwave absorptionCarbon nanotubegraded

Carbon Nanotube Decorated with Silver Nanoparticles and its electromagnetic Wave Absorption Properti

Silver (Ag) nanoparticles were fabricated by chemical reduction process,and then the Ag nanoparticles were grafted onto the surface of carbon nanotubes (CNTs) to prepare hybrid nanocomposites.

会议

Silver nanoparticlesCarbon nanotubesMicrowave absorber

Research on Crossed Nanostructure of a Cheek Tooth

The observation of a scanning electronic microscope on an adult cheek tooth shows that the tooth is a kind of natural bioceramic composite consisting of hydroxyapatite and collagen protein.

会议

大尺寸Nano-SiCp/AZ91D镁基复合材料的组织及其力学性能

与本文相关的学术论文