【摘 要】
：
Torsion simulations of strip rolling were carried out on a 0.06%C-0.3%Mn-0.01%Si steel over the temperature range 930℃ to 1000℃.Pass strains of 0.4 were applied at a strain rate of 1s?1.Interpass time
【机 构】
：
Materials Engineering,McGill University 3610 University St. Montreal,Canada H3A 0C5
【出 处】
：
第十届中国钢铁年会暨第六届宝钢学术年会
论文部分内容阅读
Torsion simulations of strip rolling were carried out on a 0.06%C-0.3%Mn-0.01%Si steel over the temperature range 930℃ to 1000℃.Pass strains of 0.4 were applied at a strain rate of 1s?1.Interpass times of 0.5s,1s,1.5s and 3s were employed to determine the mean flow stresses(MFSs)applicable to strip rolling.By means of double differentiation,critical strains of 0.04 and 0.11 were established for the initiation of dynamic transformation and dynamic recrystallization,respectively.It is shown that the dynamic transformation of austenite to ferrite takes place above the Ae3 temperature,resulting in significantly lower than expected MFS values.The nucleation of ferrite reduces the rolling load and modifies the microstructure.Shorter interpass times produce larger decreases in MFS than longer ones because of reduced recovery during short interpass intervals.
其他文献
针对钢铁行业发展面临严峻的成本挑战的现状,选择高性价比的铁矿粉对于降低炼铁成本至关重要.传统的铁矿粉性价评价方法主要有铁矿粉品位吨度价法、综合品位吨度价法、特殊成分价格折算法等,这些方法难以全面、准确地表征铁矿粉对于整个高炉炼铁系统有效的适应性;基于此,本文提出一种基于“铁矿粉-烧结-高炉炼铁”工艺流程模拟计算的铁矿粉性价评定方法,该方法综合考虑铁矿粉的价格、品位、脉石成分及其他特殊成分组成等因素
Although softening/melting tests are widely used to assess ferrous material properties in the cohesive zone of a blast furnace,there is little understanding of the mechanisms causing the softened bed
锅炉压力容器和压力管道等特种设备主要由管状承压类构件组成.由于该类设备始终处于高温、高压、冲刷及磨蚀等低周高应运行工况,其失效形式多种多样.再加上设计、制造、安装、使用、维护、修理与改造等各环节中难以避免地存在各种问题,因此,其失效原因分析往往变得更为复杂.为了分类总结30年来该类管状特种设备的技术与管理经验,文章针对短期超载超温失效,从断口金相与显微金相、宏观断口与微观断口形貌、SEM/TEM、
The reactivity of ferro-coke is much higher than the conventional coke and its application to the blast furnace is expected to improve the blast furnace reactions efficiency and to reduce fuel consump
A transient 3D mathematical model has been developed for the motion of inclusions in a continuous casting tundish with channel type induction heating.The Euler-Lagrange approach was employed,and the i
The production of Nb microalloyed coils by thin slab casting and direct rolling(TSDR)technologies shows some metallurgical characteristics that significantly differentiate this process from convention
本文介绍了一种高效全自动炼钢、炼铁炉渣分析技术,该技术实现了一条生产线四种炉渣自动无相互干扰的分析。通过将炉渣样品的全自动分析过程拆分为样品传递、样品破碎、样品研磨、样品压片等8个环节,找到了可能影响全自动压片成功率和炉渣交互污染的关键点位。利用实验设计的方法,确定了转炉渣黏结剂加入量0粒、研磨时间120 s、压片压力120 kN、保压时间10 s;确定了保护渣、精炼渣、高炉渣黏结剂加入量12粒、
随着高炉往大型化和长寿化发展,炉缸炭砖的重要性越发引人注目,但目前大高炉用炭砖还主要依赖进口.对于炉缸炭砖的质量,特别是左右炭砖寿命的抗铁水侵蚀等的重要指标方面,目前还没有特定用于大高炉炭砖的检测方法和标准.本文通过分析大高炉的工作特征,优化了高炉炭块抗铁水侵熔蚀性试验方法(GB/T 24201—2009)的测试条件,并对目前常用的多种炉缸用炭砖作了该项目的测试;通过将其测试结果和相对应的炭砖溶解
研究了回火温度对微观组织、力学性能以及低温冲击韧性的影响。结果表明:随着回火温度的升高,马氏体晶界及晶面逐渐有碳化物析出,组织中碳化物由片状连续不均匀分布变为颗粒状弥散分布;抗拉强度与屈服强度都随着回火温度的升高而下降,断面收缩率及断后伸长率随着回火温度的升高而增加;在350～450℃温度间,冲击功随回火温度升高稳定增加,回火温度在550℃以上时,冲击功呈急速升高状态,SCM435钢经油淬后在55
In order to account for the plastic surface deformation occurring in cold rolling,a novel,3-D Stribeck curve is proposed.This curve is characterised by three anchor points which represent(1)the fricti