论文部分内容阅读
随着电动车的不断发展,锂离子电池已成为了便携能源领域极为重要的一部分.相对传统的锂离子电池正极材料,富锂锰基正极材料Li2MnO3·LiMO2(M=Ni,Co,Mn)由于其超高的放电容量(＞250mAh/g)而受到了极大的关注.
层状-尖晶石复合锂离子电池富锂正极材料及性能研究
【摘 要】
：
随着电动车的不断发展,锂离子电池已成为了便携能源领域极为重要的一部分.相对传统的锂离子电池正极材料,富锂锰基正极材料Li2MnO3·LiMO2(M=Ni,Co,Mn)由于其超高的放电容量(＞250mAh/g)而受到了极大的关注.
【机 构】
：
厦门大学能源研究院 厦门大学固体表面物理化学国家重点实验室,化学化工学院,福建,厦 门,36100
【出 处】
：
第十八次全国电化学大会
【发表日期】
：
2015年7期
其他文献
Series of Experiment Research for Performance of Concrete Column Constraint by Fiber Sheet under Uni
In this paper, comprehensive summary was carried on to the recent ten years research of character of concrete column constraint by fiber sheet under uniaxial load.The research for concrete column cons
会议
A new approach for the research process of the curing reaction of thermosetting resins-dynamic torsi
The RCM-3000E Resin Curemeter would be able to monitor the cure process of thermosetting resin and resin-based composite real-time, ascertain and analysis parameters in cure process quantitatively, in
A regression analysis-based calculation method issued by CMH-17 is introduced to calculate B-Base value of multiple condition samples.The rationality and the applicable conditions of the experience-ba
本文主要介绍了CMH-17最新推荐的一种基于回归分析的合并多环境样本的B基准值统计方法，重点阐述了在批间变异检验、环境样本间的方差等同检验及正态性检验中，加入工程经验判断的合理性及适用条件。根据该多环境合并方法，设计开发了B基准值统计分析软件。采用该软件对江苏恒神股份有限公司部分复合材料力学性能数据进行了统计分析，结果表明与传统的单环境样本统计程序相比，该多环境合并方法显著地提高了B基准值，并克服
Aerogels are lightweight nanoporous solids with extremely low thermal conductivity and have been used as excellent thermal insulation materials.However, the poor mechanical properties such as low stre
Characterization of the interface properties, such as the strength, width, etc, is very important for composites, while currently it is rather difficult to characterize the single-fiber/epoxy properti
The natural spruce short fiber reinforced polypropylene composites (spruce/PP) is gradually used as the preferred material in the design of load-bearing inner components for automobile, bullet train a
采用超声阵列检测技术分别对多厚度蒙皮与粘接复合材料两种典型结构进行了试验研究，并对比分析了超声阵列检测技术和常规超声的检测能力。试验结果表明：超声阵列检测通过采集渡越时间或幅度两种信号分别进行C扫描成像，一次扫查即可完成多厚度蒙皮和粘接复合材料的检测。在达到常规超声检测能力的前提下，超声阵列检测效率远高于常规超声检测，适用于大型平面或曲面复合材料的快速检测。
为了提高纤维金属层板的刚度及损伤容限,本文研究了以铝锂合金为金属基板的新型纤维金属层板.首先,将铝锂合金由2mm冷轧至0.3mm,时效强化至T3态,并对其进行表面磷酸阳极化处理.其次,采用优化的工艺制备新型纤维金属层板,并研究其浮辊剥离、层间剪切、拉伸、弯曲及疲劳裂纹扩展等力学性能.结果 表明,铝锂合金在T3态的主要增强相为δ相,其经过阳极化处理后获得了理想的粗糙表面；所制备的新型纤维金属层板与传
A facile synthesis of Li2Fe1/3Mn1/3Ni1/3SiO4/C composites as cathode materials for lithium-ion batte
With the development of lithium-ion batteries.there are growing needs on developing low cost electrodematerials for large scale applications in electric vehicles(EV) or hybrid electric vehicles(HEV).
会议