【摘 要】
：
In the blast furnace slag, titanium disseminates in various mineral phases(perovskite, spinel, Ti-rich diopside, Ti(C、 N) and titannaugite). Based on the technique of selective precipitation, titanium
【机 构】
：
School of Materials and Metallurgy,Northeastern University,Shenyang 110004 P.R.China
【出 处】
：
2004年有色金属冶金及材料第二届国际学术会议
论文部分内容阅读
In the blast furnace slag, titanium disseminates in various mineral phases(perovskite, spinel, Ti-rich diopside, Ti(C、 N) and titannaugite). Based on the technique of selective precipitation, titanium was studied. The first step of this technique is to select the titanium enrichment phase on which the most titania can be concentrated by optimizing the heat treatment and appropriate additives. The result was made by calculation and analysis that Perovskite in the slag is the best enrichment phase. The conclusion was validated by experiments.
其他文献
本文采用热压烧结的方法制备了镍铁尖晶石基金属陶瓷试样,用于铝电解的惰性阳极.实验制得了相对密度大于98％的阳极试样,并研究了试样的导电性能和抗电解质腐蚀性能.实验结果表明,所得的阳极试样的电导率随温度的升高而增大,在900℃时电导率在40-60Ω-1·cm-1之间.在电解过程中,阳极电压降平稳(2.8～3.2V),表明阳极的电阻在电解过程中没有明显变化,导电性能稳定.用反电动势法测量电解反应的分解
本文尝试在合成镍铁尖晶石过程中添加一定量MnP2以提高试样的性能.采用高温固相反应法制备掺杂MnO2的镍铁尖晶石惰性阳极材料,研究了掺杂MnO2对制品密度、导电性和抗腐蚀性的影响.研究结果表明,MnO2能够促进烧结,提高制品的密度,并能够改善制品的导电性和抗腐蚀能力.试样经X-射线衍射分析发现,添加MnO2后,未形成新相,材料仍是镍铁尖晶石结构.
为寻求降低湿法炼锌溶液净化过程中锌粉消耗的有效途径,本文研究了砷净液除钻工艺中返渣的利用、铜离子的加入量和净化pH值等因素对净化效果的影响.实验结果表明,净液过程中将第二、三段净液渣返回第一段净液的返渣技术能大幅度降低锌粉消耗,在净液温度70℃,搅拌速度200r/min,加入碱溶砒霜100mg/L,Cu2+的加入量为20mg/L,除钴pH为4.5的条件下除钴后液残钻浓度低于0.75mg/L,可使一
在热力学分析的基础上,进行了硅热还原法回收二次资源高速钢铁鳞中的W、Mo、Cr及V合金的研究.对还原剂、石灰用量及单位热效应对合金回收率的影响进行了分析探讨.研究结果表明：采用硅热法回收工艺是可行的,W、Mo回收率在95％以上,Cr回收率大于72％,V回收率不低于45％.冶炼出的产品质量稳定,可满足炼钢使用要求.充分做到了废物利用,具有明显的经济效益和社会效益.
本文模拟铜电解精炼的工业生产条件,研究高电流密度脉冲电流法电解精炼铜的方法,并用XRD、SEM研究脉冲电流对阴极铜沉积的结构和组成的影响。研究表明,当电解温度为70℃时,脉冲电解较适宜的工艺条件为：峰电流密度600 A/m2,脉冲宽度0.01 s,占空比1：1.添加剂用量：聚丙烯酰胺2.0 mg/dm3,硫脲1.5 mg/dm3,骨胶1.0 mg/dm3.测试结果表明,采用直流电解法得到铜沉积的晶
镁合金化学镀层的孔隙率与其耐蚀性有着直接的关系.根据基体元素与相应的指示剂显色原理,采用贴试纸法,对镁合金化学镀层的孔隙率测定进行了研究,并考察了镀液参数对孔隙率的影响.通过电子扫描电镜(SEM)和镀层的耐蚀性测试,验证贴试纸法测镁合金化学镀层孔隙率可行性.结果表明,铬黑T作指示剂溶液测定镁合金化学镀层孔隙率效果最佳,镁试剂I效果次之,茜素磺酸钠指示剂最差;采用贴试纸法测定化学镀层孔隙率是可行的;
A clear zinc hydrometallurgical process-the hydrometallurgy of zinc without iron residue was proposed in this paper. By using iron and part of zinc in the zinc sulfidc concentrates and manganese in py
Nickel-sulfur electrode was obtained in a modified Watts bath by adding thiourea (TU) into the bath. The effects of TU concentration, current density, temperature and pH value of electrodepositing sol
A new type of metal matrix composite with a composition of Al2O3-33.8Fe-26.2Ni (wt.％) used as inert anode was developed in this article. Aluminum electrolysis with this anode was conducted for 12 hour
The power feeding curve of graphitized furnace is a key technique in production of the electrode. The furnace is improved in order to reduce the power consumption of the electrode, to cut short the po