• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. Low velocity impact properties of aluminum foam sandwich structurecomposites

Low velocity impact properties of aluminum foam sandwich structurecomposites

来源 :第二届中国国际复合材料科技大会 (CCCM-2) | 被引量 : 0次 | 上传用户：debug_core
【摘 要】
：
Sandwich structure composites were prepared by aluminum foam and basalt fiber, ultra-high molecular weight polyethylene(UHMWPE) fiber composite faceplate.The factors influencing the impact properties
【作 者】
：
ZHAO Jinhua CAO Hailin YAN Yiwu DING Li 
【机 构】
：
Shenzhen Key Laboratory of Composite materials,Shenzhen Academic of AerospaceTechnology,Shenzhen 518
【出 处】
：
第二届中国国际复合材料科技大会 (CCCM-2)
【发表日期】
：
2015年7期
【关键词】
：
aluminum foam sandwich structure basalt fibers UHMWPE impact properties 
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
　　Sandwich structure composites were prepared by aluminum foam and basalt fiber, ultra-high molecular weight polyethylene(UHMWPE) fiber composite faceplate.The factors influencing the impact properties and damage model of aluminum foam sandwich structure, which include the different fiber type faceplate, fabric layer design and the thickness of the core materials were studied.
其他文献
Mechanism and prevention of spontaneouswhisker growth on Cr2GaC
Spontaneous growth of A-element whiskers from MAX phase materials may bar their practical application, since it casts doubts about their stability.In this study, the growth of Ga whiskers from sintere
会议
MAX phasestabilitywhisker growthnucleation modelprevention strategy
Synergetic Effect of NbSe2Nanofibers and Cr2Nb in Cu-based Electrical Contact Composites: Tribologic
The Cu-based electrical contact composites containing reinforcement (Cr2Nb particles) and solid lubricants (NbSe2 particles) were fabricated by a powder metallurgy method, and their mechanical and ele
会议
Wear rateCu-based compositesResistivityTribological properties
Development and application of pultrusion resin used in fiber-reinforced resin matrix composite mand
Adopting multi-functional glycidylamine-ether type epoxy resin, liquid acid anhydride hardener as the basic materials, introducing in-situ phase toughening technology, the pultrusion resin composite f
会议
high temperaturecable composite mandrelpultrusionEpoxy resin
Thermodynamic Analysis of Ag/CuO·Y2O3 MultiphaseComposites Fabricated by In-Situ Synthesis
The Gibbs free energy of evaluation of Ag, Cu, and Ce was calculated.The equilibrium oxygen partial pressure of Ag, Cu, and Ce oxide was calculated.The calculate results was drew in a graph respective
会议
Ag/CuO·Y2O3in-situ synthesisthermodynamic calculationGibbs free energyequili
Radiation tolerance of Ti3SiC2 MAX phases
The ternary layered MAX-phase materials combining the merits of both metals and ceramics are considered as the candidate material for fusion reactor.The different ion beam produced by a tandem acceler
会议
MoO2/rGO/Ni三维复合超级电容器电极材料的制备与性能研究
本文采用电沉积的方法将Hummers法制备的氧化石墨烯(G0)还原沉积在金属泡沫镍基底上制备出具有三维介孔结构的还原氧化石墨烯(rGO)，并通过第二次电沉积将一层超薄MoO2沉积在rGO表面，形成了具有特殊形貌的MoO2/rGO/Ni超级电容器纳米复合电极材料。
会议
反应烧结法制备轻质多孔SiCf/SiC复合材料
本文以中间相炭微球和硅粉为原料，通过模压反应烧结法获得一种新型多孔SiCf/SiC复合材料。通过改变原料比、球磨时间、炉内压力等研究了多孔材料的微观形貌、力学性能、孔隙率及孔径分布。结果 表明，增加原料的球磨时间，多孔材料的力学性能大幅度提高，孔隙率及孔径分布下降。
会议
多孔SiCf/SiC复合材料弯曲强度气孔率
基体位置对CVD SiC涂层微观结构影响规律研究
以国产高纯石墨为基体，一甲基三氯硅烷为先驱体原料，使用化学气相沉积工艺制备了SiC涂层。利用SEM和XRD分别对筒式工装和笼式工装中不同位置所获得涂层的形貌及微观结构进行了表征，并研究了沉积速率、表面形貌、微观结构及堆积缺陷的变化规律。
会议
化学气相沉积碳化硅微观结构涂层
PAS烧结SiC-石墨复相陶瓷的阻力曲线行为和抗热震性能
采用PAS烧结工艺在1680℃成功制备出SiC-石墨复相陶瓷，并研究了石墨含量对复相陶瓷物理力学性能、韧性、R曲线(阻力曲线)行为和抗热震性能的影响。结果 表明：随着石墨含量的增加复相陶瓷的致密度、抗弯强度、弹性模量和维氏硬度均有所降低；以韧化比(TI)作为复相陶瓷的韧性指标，表明石墨含量越多，复相陶瓷的韧性越好，存在陡峭的上升R曲线行为，该指标更能反映复相陶瓷的韧性特征；显微形貌分析发现，复相陶
会议
SiC-石墨复相陶瓷韧性R曲线热震抗力
MoO2/rGO/Ni 3-Dimentional Electrode forHigh-performance Supercapacitor
The nanostructured MoO2/rGO/Ni foam 3-dimentional electrode for supercapacitor is synthesized via a two-step method.First, the graphene oxide (GO) prepared by Hummers method is electrodeposited on nic
会议