2. 您的位置
3. 首页
4. 会议论文
5. Study of reinforcement of carbon nanotube fibers by polymer infiltration via coarse-grained molecula

Study of reinforcement of carbon nanotube fibers by polymer infiltration via coarse-grained molecula

来源 :第二届中国国际复合材料科技大会 (CCCM-2) | 被引量 : 0次 | 上传用户：xxakk3321

【摘 要】

：

Carbon nanotube (CNT) fibers have attracted enormous attention because of their hierarchical structure based on CNTs that extends the excellent properties of the tubes from the nanoscale to macroscale

【作 者】

：

LIU Xia YANG Qingsheng 

【机 构】

：

College of Mechanical Engineering,Beijing University of Technology,Beijing 100124,China

【出 处】

：

第二届中国国际复合材料科技大会 (CCCM-2)

【发表日期】

：

2015年7期

【关键词】

：

carbon nanotube fiber polymer infiltration coarse-grained molecular dynamic simu 

下载到本地 , 更方便阅读

下载此文 赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

　　Carbon nanotube (CNT) fibers have attracted enormous attention because of their hierarchical structure based on CNTs that extends the excellent properties of the tubes from the nanoscale to macroscale applications.Despite intensive efforts, the mechanical properties of CNT fibers still fall short of expectations.

其他文献

三维编织石英纤维预制体压缩回弹性能试验研究

针对航天密封材料的使用特性,引入了三维编织结构石英纤维预制体作为热密封件。室温下测试了三维编织结构石英纤维预制体的单向压缩、循环压缩和应力松弛性能。试验结果表明：三维编织结构预制体具有良好的可压缩性,压缩应变可达到60％；循环压缩的首次压缩变形后瞬时能够达到近似完全回弹,峰值载荷随后续循环次数的增加呈非线性降低,10次压缩循环后,回弹率一般仍可达到70％以上；应力松弛曲线分为两个阶段：快速松弛阶段

会议

热密封三维编织石英纤维压缩性能应力松弛

复合材料曲型加筋板的建模方法和自由振动

针对复合材料曲型加筋板，基于有限单元法，研究了其建模方法和自由振动。基于层合板理论，及Mindlin-Reissener板理论，对复合材料层合板进行建模；同时基于Timoshenko梁理论，对曲型加强筋进行建模。曲型加强筋可任意铺设在板上，而无需与板共节点。同时当筋的数量位置发生改变时，无需对板进行再次划分网格。

会议

复合材料曲型加筋板有限单元法建模方法自由振动

铺层方式对复合横担中复合材料管承载力影响的研究

本文通过有限元软件msc.marc对不同铺层结构的复合材料管进行屈曲分析，并对500kV复合横担塔进行受力分析，得出左横担中支柱绝缘子所受的最大轴力和弯矩，并将轴力和弯矩分别加载至支柱绝缘子的实体模型中，计算不行铺层结构各层最大应力，得出相关结论.

会议

支柱复合绝缘子铺层结构复合横担

Based on fine plait piercing technology of the steel matrix stiffness optimization of finite element

This paper briefly describes the characteristic of fine weave pierced fabric, which is pre-disposing needle array in Z direction and integrated piercing woven fabrics in X-Y direction.This paper also

会议

fine weave piercingmodel of elementthe overall stiffness of the steel matrixt

Macroscopic Elastoplastic Deformation of Nanoporous Materials withMultiple Interface Residual Stress

Nanoporous materials usually produce interface residual stresses, which inevitably have effects on the overall elstoplastic mechanical behaviors of such materials.The present work aims to develop a mi

会议

The design and optimization of carbon fiber laminates based on thermal stability and equal bending r

For special applications of carbon fiber composite material reflecting mirror,laminate ply design and optimization conducted on the thermal stability of composite laminates and bending stiffness unifo

会议

The numerical research of temperature fieldduring resin transfer molding

Temperature field is the most important factor during resin transfer molding of resin-based composite materials.Temperature field that Influences the process infiltrating porous media using resin was

会议

compositesResin transfer moldingtemperature fieldCFDNumerical analysis

复合材料共形天线结构研究

本文介绍了复合材料共形天线结构(Conformal Antenna Composite Structure,CACS)的设计和制造及试验结果.CACS集通讯、承载、维形等功能于一体,是一种新型多层复合材料智能蒙皮天线结构.为了避免在成型过程中,胶膜覆盖微带阵列天线的发射单元,削弱微带阵列天线的电性能,设计了封装盒盖对微带阵列天线进行封装.封装盒盖通过胶膜与4×8微带阵列天线粘结为封装天线,然后植入

会议

复合材料共形天线封装盒盖

Research On The Layer-pattern Influence To Bearing Capacity Of Composite Tube Tn Cross Arm

In this paper, the finite element software msc.marc is used to analyze composite tubes with different layer structures.Firstly, the bulking loads of different layer structure tubes are obtained by bul

会议

post composite insulatorlayer structurecomposite cross arm

A nonlinear cohesive/friction coupled model for shear induceddelamination of adhesive composite join

This paper proposes a nonlinear cohesive/frictional contact coupled model for the mode-Ⅱ shear delamination of composite adhesive joint based on a modified Xu and Needlemans exponential cohesive model

会议

Cohesive/friction couplingComposite adhesive jointsMode-Ⅱ shear delaminationF