论文部分内容阅读
本文以GCr15 钢的碳化物液析、碳化物带状级别为突破口，结合现场工艺条件，调整轴承钢加热工艺，完善轴承钢的加热制度，并对调整完善后的效果进行对比分析。确定较为合理的轴承钢加热工艺参数。
GCr15钢加热工艺与液析及带状的关系
【摘 要】
：
本文以GCr15 钢的碳化物液析、碳化物带状级别为突破口，结合现场工艺条件，调整轴承钢加热工艺，完善轴承钢的加热制度，并对调整完善后的效果进行对比分析。确定较为合理的轴承钢加热工艺参数。
【机 构】
：
莱芜钢铁股份有限公司,山东莱芜 271105
【出 处】
：
2011特钢年会
【发表日期】
：
2011年5期
其他文献
采用数值模拟方法对自然置换通风、自然层状通风、自然顶部通风三种自然通风方式室内温度场和速度场进行研究，以获取三种自然通风方式中室内热舒适性，寻求各自然通风方式适用范围。研究结果显示，三种自然通风方式中人体头部与脚踝之间垂直温差均小于5℃，满足人体热舒适对垂直温差的要求。自然置换通风、自然顶部通风在人体呼吸区高度上气流速度分布比较均匀，除进风口以及出风口附近区域其他区域气流速度均小于引起人体不舒适的
利用等离子喷涂技术制备NiCr 作为粘接层的P7412 陶瓷涂层。采用失重法研究了涂层在3.5％NaCl 溶液中的腐蚀速率。用SEM 观察涂层腐蚀前后的表面形貌，并用动电位极化曲线和电化学阻抗谱（EIS）技术研究涂层的腐蚀机理。根据陶瓷涂层的特殊结构，建立等效电路图并进行拟合分析。结果表明，粘接底层/基体界面腐蚀产物会影响涂层失重。氧化膜的生长与溶解以及腐蚀二次产物的积累共同导致了涂层重量出现周期
Continuous inkjet (CIJ) technology has the advantage of much higher speed, better reliability, and wider ink and substrate latitude compared to drop-on-demand (DOD) inkjet technology. KODAK Stream Ink
MEMS Industry is growing double digits now and will continue its fast growth for the next decade.Bosch is one of the earliest pioneers of the MEMS technology, and invented the famous Bosch Process.MEM
Plasma, eYCited with microwave energy, has Very interesting properties which are in direct correlation with the eYCitation frequency. This is due to the reachable high electron density, which itself h
This presentation introduces a new IC architecture and design technique which can be widely used for MEMS based sensors and wireless applications. The presented digital predistortion technique can ach
After many years developing, MEMS is getting blooming in consumer filed and become one of the driving force of new applications, especially Internet of Things since 2009. As the smart nodes on the IOT
There is a big boost in demand of MEMS in the last two years driven by their use in consumer applications such as smart phones, tablets and gaming consoles. Yole Developpment predicts about 14％compoun
The Medical Research Council and the UK Clinical Research Collaboration awarded a ＃4 million grant to the consortium of academic and industrial researchers to improve seYUal health through the use of
The "Hands-on access fab" is a 4" and 6" facility that companies can easily access and utilize for their prototyping. The fab is shared with other users and managed with best efforts. The fab will not