• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. Numerical simulation study of the curing process of large thickness composite

Numerical simulation study of the curing process of large thickness composite

来源 :第二届中国国际复合材料科技大会 (CCCM-2) | 被引量 : 0次 | 上传用户：wufato
【摘 要】
：
　　Numerical simulation method was used to study the curing process of considerable thickness X850 toughened epoxy resin laminate.The affection of heating to t
【作 者】
：
XUPeng;YANDongxiu;LIUWeiping;SUNKai;KONGJiaoyue;DONGLiushan; 
【机 构】
：
Institute of Aeronautical Manufacturing Technology,Shanghai Aircraft Manufacturing Corporation Ltd.,
【出 处】
：
第二届中国国际复合材料科技大会 (CCCM-2)
【发表日期】
：
2015年期
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
　　Numerical simulation method was used to study the curing process of considerable thickness X850 toughened epoxy resin laminate.The affection of heating to the temperature control was studied during the comparison of two different curing cycles, and the heat release, as well as the highest temperature in the central area was analyzed.
其他文献
Research ongraphene/poly(vinyl alcohol) nanocomposite
　　Graphene with its unique propertieshas a bright future in the application of composite materials.In this study, for graphene oxide (GO) as the precursor, ba
会议
Effect of Stitching on Mechanical Properties of MT300 Carbon Fabric/EpoxyComposites
　　Stitched MT300carbon fabric/epoxycomposites were prepared by RTM process.The effects of stitching density, stitching orientation, and combination of stitchi
会议
Experimental study on the elastic recovery effect of fabric preform in vacuum infusion molding proce
　　Through the monitoring of fabric preform thickness and fiber volume fraction changes with resin in-plane flow and out-plane flowin vacuum infusion molding p
会议
Design and Production of Filament-wound Composite Pressure Vessels
　　The conventional filament winding process is primarily relying on the geodesics, semi-geodesics or planar winding patterns, which exhibit fewer degrees of d
会议
Research on hot-press bonded mechanism and designing for Prepreg
　　According to the requirement of high efficiency and high reliability for prepregchange in Automatic Placement and Tape Winding, the theology theory and the
会议
Modeling of Cutting Forces in Turning of Al/SiC composites
　　Changing of cutting force has an important effect on metal cutting process in cutting aluminum-based SiC particle reinforced metal matrix composite(MMCs).An
会议
The Optimization of Composite Material Winding Strategy Based on Robot
　　The industrial robot with the characteristic of multi degree of freedom, good flexibility, high repeated accuracy and strong expansibility, is widely used i
会议
Design and Applicationof the Wireless Transmission Tension Test-controlled System based on PLC
　　The wireless transmission tension test-controlled system automatic controlled by PLC has been introduced according to the winding tension of the vertical wi
会议
The study on Automated Fiber Placement system for thermoplastic composite
　　The fiber reinforced thermoplastic composite has broad prospects in aerospace field due to its advantages of high specific strength, high specific modulus,
会议
Analysis of design temperature for autoclave
　　Analyzing the influence of the design temperature for autoclave.In order to obtain the temperature distribution of main pressure part for autoclave,building
会议