【摘 要】
：
Nano-titania/polymer composites were prepared and their anti-icing property was studied.The water contact angle of the composite materials was measured and their anti-icing capability was determined.T
【机 构】
：
Institute of New Materials, Shandong Jiaotong University, Jinan, China, 250023
【出 处】
：
2011中国功能材料科技与产业高层论坛
论文部分内容阅读
Nano-titania/polymer composites were prepared and their anti-icing property was studied.The water contact angle of the composite materials was measured and their anti-icing capability was determined.The results demonstrate that the anti-icing prperty of the composite materials depends not only on their superhy-drophobicity but also on the surface morphology.The result provides a comprehensive framework for optimazing nanoparticle/polymer composite for a wide range of applications.
其他文献
MoO3 submicrobelts with the radial direction of less than 500 nm were successfully synthesized with ammonium paramolybdate as molybdenum source and nitric acid as precipitant at 240 ℃ for 48 h with pH
在不同压紧压力条件下得到不同装填密度的改性纤维球与纤维球过滤器,本文对纤维球过滤器和金属多孔膜去除油气田回注污水中油份和悬浮物进行了研究.实验结果表明在相同压紧压力下改性纤维球装填密度、吸附原水量明显大于未改性纤维球,且高密度的改性纤维球表现出去除油份能力显著,但去除悬浮物效果不明显,金属多孔膜表现出稳定的去除油份及悬浮物的能力.
本文采用挂浆法和粉末冶金工艺制备镍基合金空心球.探讨了原始合金粉末、造孔模板、粉浆粘度、烧结工艺等对空心球的结构形成的影响规律.实验结果表明,非球形粉末的原始粒度越小,毛坯球表面越均匀、光滑,球壳壁厚越薄,烧结后空心球壳孔隙率越少,强度越高;直径约为3mm的聚苯乙烯球有利于制得球壳均匀、孔隙率较低的空心球;粘结剂的浓度越大、液固比越大,涂覆的毛坯球的壁厚也就越大,不同浓度的粘结剂选择合适的液固比,
纳/微米结构功能及其复合材料在锂离子电池、催化、驱动器件、传感器、智能变色窗口与器件,超级电容器等领域有许多重要的应用.为获得性能调控,具有特异形貌纳/微米结构功能及其复合材料适用于不同领域的应用,采用水热方法制备了可控形貌的低维钒氧化物.考察了数种典型软模板的存在对其形貌的影响.采用扫描电镜(SEM),透射电镜(TEM),X-射线衍射(XRD),傅里叶红外(FTIR)等进行了相应表征.结果表明,
Barium ferrite microfibers/poly (vinylidene fluoride) (BaFe12O19/PVDF) composite films were prepared by the solution casting process.The X-ray diffraction analysis indicates the BaFe12O19 microfibers
K2Ti6O13 whiskers (KTOw,0~1.5 wt%) toughened (Pb0.70Ba0.26Sr0.04)(Zr0.52Ti0.48)O3 (PBZT) ceramic composites were prepared by the solid state reaction method.Their structure,mechanical,piezoelectric pr
采用水稀释法研究丙烯酰胺(AM)反相微乳液相区,然后紫外光照引发聚合生成聚丙烯酰胺(PAM)微胶乳,再对其改性制得PAM反应性微凝胶.对产物的结构和形貌进行了表征,并探讨了其作用机理.稳定的反相微乳液外观澄清透明,离心后不分层,PAM反应性微凝胶粉末为球形或类球形,具有明显的团聚现象,颗粒粒径在200nm～400nm之间,其作为交联剂质量分数在0.9％～1.1％时,交联产物韧性较好.
Hierarchically mesoporous silica coated superparamagnetic microspheres with an uniform particle diameter of 750-800 nm and shell thickness of 65-100 nm were synthesized utilizing the surfactant-templa
采用自制的铝酸镁粉体分别混合自制和市售的荧光粉制备透明荧光陶瓷,将透明荧光陶瓷加工并替代传统白光LED中的荧光粉层和环氧树脂封装外壳对LED进行封装.测试了不同掺杂浓度和不同厚度的透明荧光陶瓷封装的LED器件的部分光电性能,讨论了厚度和浓度对光电参数的影响.由于荧光转换物质在透明陶瓷中均匀分布,解决了传统工艺中荧光粉易沉降的问题,有利于出光的均匀性;陶瓷材料比树脂等有机材料热导率高,有助于解决散热
针对常规吸水树脂材料吸水速率快无法实现油田深部调剖的问题,根据Flory的吸水理论,研究同时使用稳定和不稳定的交联剂,采用直接聚合和互穿网络两种方法,制备了高交联度的吸水凝胶材料.并对材料的吸水性能及弹性强度进行了测试,用扫描电镜(SEM)观察了样品的表面形态.研究表明:高交联度的不稳定交联剂能起到一定的缓膨效果,但是作用时间短;用互穿网络的方法比常规共聚有更高的强度;针对此研究结果,提出了吸水树