2. 您的位置
3. 首页
4. 期刊论文
5. Investigation on synthesis of a low cost no-bake furan resin system with a high strength

Investigation on synthesis of a low cost no-bake furan resin system with a high strength

来源 :中国铸造：英文版 | 被引量 : 0次 | 上传用户：skynan2001

【摘 要】

：

The synthesis of a low cost no-bake furan resin with a high strength was researched in this paper. Through the analysis of main factors influencing the strength

【作 者】

：

Liu Weihua Liu Shiyang Li Ying 

【机 构】

：

SchoolofMaterialsScienceandEngineering

【出 处】

：

中国铸造：英文版

【发表日期】

：

2014年5期

下载到本地 , 更方便阅读

下载此文 赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

The synthesis of a low cost no-bake furan resin with a high strength was researched in this paper. Through the analysis of main factors influencing the strength of furan resin, an orthogonal experiment was conducted to optimize synthesis of urea-formaldeh

其他文献

Grain refinement of AL-3.5FeNb-l.5C master alloy on pure A1 and M-9.8Si-3.dCu alloy

期刊

Role of heat treatment in the improvement of mechanical properties of a high-quality Al-11Si- 1.5Cu-

The purpose of this study is to prepare a high-quality Al-11Si-1.5Cu-0.3Mg casting alloy with a good combination of strength and ductility. The microstructures

期刊

Climate history of the middle reach of the Yangtze river over the past 9000 years: A speleothem isot

A stalagmite in Qingjiang, Hubei, has yielded the records of hydrogen and oxygen as well as carbon isotopic changes and provided a climate history of 9000 years

期刊

themiddleREACHofYangtzeriverstableisotopeclimatehistory.the middle rea

Numerical simulation of central shrinkage crack formation in a 234-t steel ingot

中央收缩快克是在钢铸块锭扔遇到的一个普通缺点。在前进在进一步的繁殖的情况下限制快克的度是必要的。A 234-t 钢铸块锭被把在宽度在高度和 120 公里检查内部质量，和 1,400

期刊

收缩快克有限元素裂缝潜力thermo机械的模拟钢铸块锭TP391.99一shrinkage crack finite-element crack

Microstructure evolution of ZA72 magnesium alloy during partial remelting

The application of some semi-solid forming magnesium alloys is restricted due to their weak mechanical properties. To improve the mechanical properties, it is n

期刊

Evolution of microstructure and mechanical properties of A356 aluminium alloy processed by hot spinn

微观结构的进化和合金使遭到了到热旋转过程的 A356 铝的机械性质被调查了。结果显示变丑处理一致微观结构并且改进了 A356 铝合金的机械性质。在热旋转过程期间，最容易溶解的

期刊

热旋转过程A356铝合金微观结构机械性质TG146.21Ahot spinning process A356 aluminum alloy mic

Effect of cooling rate and forced convection on as-cast structure of 2205 duplex stainless steel

To forecast the as-cast structure and ferrite-austenite phase ratio of 2205 duplex stainless steel(DSS), the effects of cooling rate and forced convection were

期刊

Effect of centrifugal counter-gravity casting on solidification microstructure and mechanical proper

To investigate the influence of Centrifugal Counter-gravity Casting(C3) process on the solidification microstructure and mechanical properties of the casting, A

期刊

Influence of MTi3C0.15 modification treatment on damping properties of ZnAII0 alloy

Zn-AI alloys constitute an interesting group of foundry alloys. Due to a relatively low meltingtemperature, they allow a decrease in energy-consumption of the m

期刊

MODIFICATIONDAMPINGDAMPINGCOEFFICIENTZINCALLOYSZnAIIOULTRASOUNDwavemodi

Modii cation ef ect of calcium-magnesia phosphate fertilizer on microstructure and mechanical proper

In order to modify in-situ synthesized Mg2Si particles in Mg2Si/Mg-4Si composite, the modif ication effect of calcium-magnesia phosphate fertilizer on primary M

期刊

hotcrackCOMPOSITEcalcium-magnesiaphosphatefertilizermodificationMG2SIfer