Linear optics calibration and nonlinear optimization during the commissioning of the SSRF storage ri

来源 :中国物理C | 被引量 : 0次 | 上传用户:bolinyuan
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Phase I commissioning of the SSRF storage ring on 3.0 GeV beam energy was started at the end of December 2007. A lot of encouraging results have been obtained so far. In this paper, calibrations of the linear optics during the commissioning are discussed, and some measured results about the nonlinearity given. Calibration procedure emphasizes correcting quadrupole magnetic coefficients with the Linear Optics from Closed Orbit (LOCO) technique. After fitting the closed orbit response matrix, the linear optics of the four test modes is substantially corrected, and the measured physical parameters agree well with the designed ones. Phase I commissioning of the SSRF storage ring on 3.0 GeV beam energy was started at the end of December 2007. A lot of encouraging results have been obtained so far. In this paper, calibrations of the linear optics during the commissioning are discussed, and some measured results about the nonlinearity given. the calibration curve emphasizes quadrupole magnetic coefficients with the Linear Optics from Closed Orbit (LOCO) technique. After fitting the closed orbit response matrix, the linear optics of the four test modes is substantially corrected, and the measured physical parameters agree well with the designed ones.
其他文献
核反应堆压力容器作为核电站不可更换的关键性设备,其设备完整性对核电站的安全运行起着至关重要的作用.在辐照条件下,反应堆压力容器钢中会形成一系列微结构缺陷,包括溶质沉
The ambiguity of the structure of ~(12)Be especially in the configuration of Be ground state has attracted a lot of attention recently.We notice that the nuclea
钢结构厂房中的十字型梁没有专门型材,需要两种型材拼焊。由于结构限制,普通埋弧焊接设备无法施焊,且手工拼焊不能保证质量,需要设计专用焊接设备。为了保证十字形梁焊接精度
近几年电子工业对小型化、薄型化提出越来越高要求。日本福田金属箔粉工业集团先前已经开发了亚微米级银片,可形成具有良好导电性能的导电网络。最近由于银价猛涨,于是该集团
应用定量化的分析工具,对加工中心立柱结构进行了可适应动态设计过程分析。提出产品可适应性的综合评价指标,建立了产品可适应性综合评价模型。应用多级模糊综合评价方法在对
采用多孔介质模型对蒸汽发生器二次侧流场进行分析。通过在多孔介质模型控制方程中添加附加的动量源项和能量源项来模拟蒸汽发生器内构件影响,动量源项中考虑下降段、管束、
通过对流域各地经济增长水平、流域产业结构演进水平、城镇化水平、市场化程度以及科技发展水平的分析,研究表明长江流域经济发展水平差异显著,基本呈阶梯状分布,下游最高,中
探讨了深冷处理对LC9铝合金力学性能和摩擦因数的影响。结果表明,深冷处理后LC9铝合金的硬度、弹性模量、硬弹比和弹性回复系数分别为2.54 GPa、72.61 GPa、0.035和57.95%,较
在社会经济发展过程中,如何处理官民、政企乃至计划和自由的关系,是任何一个国家都极为重视而又难于把握其最佳结合点的问题。在这方面,日本的经验值得研究,尤其是其在经济决
Based on two-dimensional(2D) rigid-plastic finite element(FE) method, the optimum observation area for metallographic microstructure and the influence of the he