【摘 要】
：
Carbon nanotubes (CNTs) were deposited uniformly on carbon cloth by electrophoretic deposition (EPD). Thereafter, CNT-doped clothes were stacked and densified by pyrocarbon via chemical vapor infiltration to fabricate two-dimensional (2D) carbon/carbon (C
【机 构】
：
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 7100
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
Carbon nanotubes (CNTs) were deposited uniformly on carbon cloth by electrophoretic deposition (EPD). Thereafter, CNT-doped clothes were stacked and densified by pyrocarbon via chemical vapor infiltration to fabricate two-dimensional (2D) carbon/carbon (C/C) composites. Effects of EPD CNTs on interlaminar shear performance and mode Ⅱ interlaminar fracture toughness (GⅡc) of 2D C/C composites were investigated. Results showed that EPD CNTs were uniformly covered on carbon fibers, acting as a porous coating. Such a CNT coating can obviously enhance the interlaminar shear strength and GⅡc of 2D C/C composites. With increaing EPD CNTs, the interlaminar shear strength and GⅡc of 2D C/C composites increase greatly and then decrease, both of which run up to their maximum values, i e, 13.6 MPa and 436.0 J·m-2, when the content of EPD CNTs is 0.54 wt%, 2.27 and 1.45 times of the baseline. Such improvements in interlaminar performance of 2D C/C composites are mainly beneficial from their increased cohesion of interlaminar matrix, which is caused not only by the direct reinforcing effect of EPD CNT network but also by the capacity of EPD CNTs to refine pyrocarbon matrix and induce multilayered microstructures that greatly increase the crack propagation resistance through “crack-blocking and -deflecting mechanisms”.
其他文献
We investigated synthesis and characterization of melamine-urea-formaldehyde (MUF) microcapsules containing n-alkane mixture as phase change core material for thermal energy storage and low-temperature protection.The phase change microcapsules (microPCMs)
NaCl aqueous solution (15wt%) was used as the quenching medium to prepare amorphous Lithium-Zinc ferrite hollow microspheres (LiZn FHMs) based on self-reactive quenching technology. Investigations by scanning electro microscope, X-ray diffraction, electro
The interaction mechanism and phase evolution of ammonium polyphosphate (APP) mixed with muscovite (APP/muscovite) were studied by TG, XRD and SEM, respectively, during heating. When the temperature is not higher than 300℃, muscovite has no effect on the
The objective of this paper was to develop a comprehensive evaluation method and index to evaluate the performance of sealants and fillers for cracks in asphalt concrete pavements using the method of principal component analysis.The performance experiment
The arc erosion under medium direct currents in the argon flow was tested on tungsten-copper (W-Cu) contacts which were processed by hot extrusion and heat treatment. The scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were u
A multifunctional amine,1,4-bis(2,4-diaminophenoxy)benzene(14BDAPOB),was prepared and used as a novel hardener for novolac epoxy resin(ER).The structure of 14BDAPOB was characterized with Fourier transform infrared(FT-IR)spectroscopy and differential scan
Drying shrinkage of thermal insulation mortar with glazed hollow beads was measured by a vertical length comparator, and the influences of fly ash with different contents (0, 18%, 36%, and 54%were used) on the long-term drying shrinkage were discussed. Th
According to the results of accelerated tests of acidiifcation corrosion depth and compressive strength of concretes subjected to sulfuric acid environments, the acidiifcation depth laws of concretes were predicted based on the grey system theory. Thus, t
Nylon 10T and nylon 10T/1010 samples were synthesized by direct melt polymerization.The isothermal crystallization kinetics of nylon 10T and nylon 10T/1010 was investigated by means of differential scanning calorimetry(DSC).The crystallization kinetics un