论文部分内容阅读
测量了准分子激光泵浦氢气产生一阶斯托克斯光的远场发散角。结果表明光束质量基本不随氢气压力变化, 主要由泵浦光泵浦聚焦参量确定。
聚焦参量对斯托克斯光远场发散角的影响
【摘 要】
：
测量了准分子激光泵浦氢气产生一阶斯托克斯光的远场发散角。结果表明光束质量基本不随氢气压力变化, 主要由泵浦光泵浦聚焦参量确定。
【机 构】
：
中国科学院上海光机所,上海201800
【出 处】
：
中国激光
【发表日期】
：
1998年25期
其他文献
Thermally enhanced responsivity in an all-silicon optical power monitor based on defect-mediated abs
We demonstrate a high responsivity all-silicon in-line optical power monitor by using the thermal effect to enhance the quantum efficiency of defect-mediated absorption at 1550 nm. The doping compensation technique is utilized to increase the density of l
期刊
The precise alignment of a high-performance telescope is a key factor to ensure the imaging quality. However, for telescopes with a wide field of view, the images are sometimes under-sampled. To study the effects of under-sampled images on the precision o
A large-mode-area (LMA) ytterbium-doped photonic crystal fiber (PCF) with core NA of 0.034 and core diameter of 50 μm was made by the stack-and-draw technique. The core is formed by Yb3 /Al3 /F /P5 co-doped sil
1981年6月中旬，我们受科学院和上海光机所的派遣，接受苏联科学院通讯院士西伯利亚自动化与电测所所长、全苏第七届瓦维洛夫非线性光学会议主席的邀请,参加了这届会议，会议的地点在新西伯利亚科学城。
期刊
对表面已进行喷砂处理的增材制造TC4钛合金在氩气环境下进行激光抛光实验,通过极化曲线测试研究了抛光前、后钛合金的耐蚀性,并结合表面粗糙度、晶粒尺寸、表面残余应力以及显微组织分析了激光抛光对TC4钛合金耐蚀性的影响。研究结果表明:抛光钛合金的自腐蚀电位与自腐蚀电流密度均大于未抛光钛合金,说明抛光钛合金相比于原始钛合金的被腐蚀倾向更小,但其一旦受到腐蚀,腐蚀速率会略大于原始钛合金。自腐蚀电位的升高源于钛合金表面粗糙度的降低,自腐蚀电流密度的增大则是因为表面晶粒的细化以及残余拉应力的存在。
We propose a novel in-band optical signal-to-noise ratio (OSNR) monitoring method based on polarization interference. The method realizes a monitoring accuracy of ±0.5 dB within the range of 9–34 dB. Our results indicate that the proposed method is transp
The influence of the axial relative motion between the target and the source on ghost imaging (GI) is investigated. Both the analytical and experimental results show that the transverse resolution of GI is reduced as the deviation of the target’s center p
The relative band gap for a rhombus lattice photonic crystal is studied by plane wave expansion method and high frequency structure simulator (HFSS) simulation. General wave vectors in the first Briliouin zone are derived. The relative band gap as a funct
报道了采用Cl2/N2电感耦合等离子(ICP)组合体刻蚀工艺在InAs/GaSb II类超晶格红外焦平面台面加工过程中的研究结果, 实验采用分子束外延技术在GaSb衬底上生长的PIN型超晶格材料。结果表明, 气体流量比例直接对刻蚀速率和刻蚀形貌产生影响, 氯气含量越高, 刻蚀速率越大, 当氮气含量增加, 刻蚀速率降低并趋于一定值。当氯气和氮气的流量比例和等离子腔体内压力等参数一定时, 随着温度升高, 刻蚀速率和选择比在有限范围内同时线性增大, 台面的倾角趋于直角, 台面轮廓层状纹理逐渐消失, 但沟道内变得