Status adaptive routing with delayed rebroadcast scheme in AODV-based MANETs

来源 :The Journal of China Universities of Posts and Telecommunica | 被引量 : 0次 | 上传用户:poabc123
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
An efficient solution is proposed in this article to determine the best reliable route and to prolong the lifetime of the mobile Ad-hoc networks (MANETs). In the proposed solution, the route discovery process of the Ad-hoc on-demand distance vector routing protocol (AODV) has been modified using a novel delayed rebroadcast scheme. It combines the shortest route selection criterion of AODV with the real network status including the wireless link quality, the remaining power capacity, as well as the traffic load at each node. Simulation results show that the proposed scheme can significantly extend the network lifetime and provide fewer packet losses than the conventional AODV protocol. An efficient solution is proposed in this article to determine the best reliable route and to prolong the lifetime of the mobile Ad-hoc networks (MANETs). In the proposed solution, the route discovery process of the Ad-hoc on-demand distance vector routing protocol (AODV) has been modified using a novel delayed rebroadcast scheme. It combines the shortest route selection criterion of AODV with the real network status including the wireless link quality, the remaining power capacity, as well as the traffic load at each node. results show that the proposed scheme can significantly extend the network lifetime and provide fewer packet losses than the conventional AODV protocol.
其他文献
麻疹曾是严重危害儿童身体健康的急性传染病之一。龙岩市控制麻疹数十年历经了疫苗使用前、预防接种和计划免疫等不同阶段 ,到 1999年麻疹发病率降至历史最低水平 ,且连续5年
以宽度为10mm的矩形槽劈挤成形为研究对象,利用正交试验原理安排试验内容,借助数值模拟和物理模拟方法,研究了尖头劈楔劈挤矩形槽的变形过程,将其划分为劈入、过渡、稳态变形
会议
设计一种特殊的弯曲卷边模具,解决盒形件的卷边问题。实践证明,新的卷边工艺方法比传统的机械卷边工艺和传统的模具卷边工艺效益高、成形可靠、产品质量好、模具寿命长。对此
轴类大锻件的锻造过程分为压方、拔长和倒棱滚圆三大步骤。目前对锻造工艺的研究中,集中在拔长工艺的优化上,忽略了压方和倒棱滚圆对锻件质量的影响。为制定准确的压方工艺参
会议
体积成形可以从宏观和微观两方面进行研究,宏观较注重坯料在模具中的填充性及材料利用率等,而微观则着眼于成形过程中动态再结晶。微观损伤等微观组织的演化。本文首先概述了
回弹是扳料冲压成形中普遍存在的现象,对成形零件的尺寸精度有很大的影响。本文以半圆柱形模具为研究对象,利用有限元分析软件ABAQUS对该模型进行成形和回弹模拟。通过小幅改
本文描述了公司在研发某自主品牌轿车自动变速器上某个重要冲压零件的时候,对遭遇的“瓶颈”问题进行攻关的过程,并对这一结果给出了自己的解释。
针对环件轧制的特点,结合环件碾扩机的工作原理,建立精确轧制几何模型,分析了轧制过程中几何形状变形规律,推导出导向辊的运动轨迹。利用数学软件对导向辊运动过程中的角速度
会议
以圆柱体大头位于中段和端部两种常见直长轴类模锻件为研究对象,运用数值模拟和物理实验相结合的方法,探讨了不经制坯直接终锻时坯料尺寸与填充效果的关系。结果表明:坯料截
在现代化大工业生产的年代里,高速级进冲压高亢着优美的旋律、振动美丽的翅膀伸展到各项冲压生产领域。比如:“空调”的翅片高速级进冲压,家用电器的电机定、转子冲片高速级