【摘 要】
：
Mg-Zn-Zr series Mg alloys (ZK) are one of the most important commercial Mg alloys due to their good comprehensive mechanical properties.The phase equilibria of the Mg-Zn-Zr system at 400 ℃ covering the overall composition range were investigated by X-ray
【机 构】
：
State Key Lab of Powder Metallurgy, Central South University, Changsha 410083, China;School of Mater
论文部分内容阅读
Mg-Zn-Zr series Mg alloys (ZK) are one of the most important commercial Mg alloys due to their good comprehensive mechanical properties.The phase equilibria of the Mg-Zn-Zr system at 400 ℃ covering the overall composition range were investigated by X-ray diffraction and electron probe microanalyses on thirteen ternary alloys.Three ternary compounds,τ1,τ2 and τ3,were detected to be thermodynamically stable at 400 ℃,and their homogeneity range was determined to be Mg(7-17)Zn(80-88)Zr(4-6),Mg(15-22)Zn(66-68)Zr(9-16) and Mg9Zn68Zr23 (in at.％),respectively.Eight three-phase regions and four two-phase regions were observed.The maximum solubility of Mg in Zn22Zr,Zn39Zr5 and Zn3Zr phases was measured to be 0.52,0.37 and 0.99 at.％,respectively,while the solubility of Zr in MgZn2 and Mg2Zn3 phases is negligible.The isothermal section of the Mg-Zn-Zr system at 400 ℃ was then constructed based on the present experimental data.
其他文献
The Ni3Al-based superalloy was rapidly solidified in the form of droplets with varying diameters.The cooling rate (Re) is a function of diameter (D) of droplet.With the decrease in droplet sizes (increase in the cooling rates),the volume fraction of γ\'
Compared to the traditional one-by-one method,a new high-efficiency method is used to characterize large numbers of regulations varying samples.Accordingly,bump-shaped electrodes are designed using the computational fluid dynamics model,and the effect of
As-extruded Mg-Sr alloy,a kind of promising biodegradable biomedical material,was coated using micro-arc oxidation and also using a phosphate conversion coating.The corrosion behaviors were investigated using Hanks\' solution.The corrosion of the as-ext
This work discusses tribological properties of commercial pure (CP) titanium processed by multi-directional forging (MDF) up to six passes at room temperature and 220 ℃.For this purpose,wear test was conducted by dry sliding pin-on-disk method on the init
The microstructural evolution of pure nickel treated by deep rolling (DR) technique with different indent depths was investigated by means of optical microscopy and transmission electron microscopy.The surface roughness,hardness and residual stress distri
The synergistic effect of NaC1 and SO2 on the atmospheric corrosion of zinc has been studied at equivalent total but different ratios of molar deposition rate under wet-dry cyclic conditions.The results show that the corrosion rates,corrosion morphologies
Carbon fiber reinforced plastics (CFRP) are promising lightweight materials for vehicle applications.316L is one of the most widely used types of austenite stainless steels and applied in lots of automotive applications.The existence of crevices will resu
The present work describes the effect of deposition potentials on structural,morphological,optical,electrical and photoconductivity responses of cuprous oxide (Cu2O) thin films deposited on fluorine-doped tin oxide glass substrate by employing electrodepo
The surface of AISI 1045 steel specimens was modified via two duplex surface treatments of (i) titanium diffusion coating followed by plasma nitriding (Ti-PN) and (ii) plasma nitriding followed by titanium diffusion coating (PN-Ti).A comparative study on
Type I hot corrosion behavior of SiO2-Al2O3-glass composite coating based on Ti-47Al-2Cr-2Nb substrate was investigated in the mixture salt of 25 wt％NaCl + 75 wt％Na2SO4 at 850 ℃.The results showed that there was a bidirectional ion exchange between compos