Uplift of Symmetrical Anchor Plates by Using Grid-Fixed Reinforced Reinforcement in Cohesionless Soi

来源 :中国海洋工程(英文版) | 被引量 : 0次 | 上传用户:lpf811
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Uplift response of symmetrical anchor plates with and without grid fixed reinforced (GFR) reinforcement was evaluated in model tests and numerical simulations by Plaxis. Many variations of reinforcement layers were used to reinforce the sandy soil over symmetrical anchor plates. In the current research, different factors such as relative density of sand, embedment ratios, and various GFR parameters including size, number of layers, and the proximity of the layer to the symmetrical anchor plate were investigated in a scale model. The failure mechanism and the associated rupture surface were observed and evaluated. GFR, a tied up system made of fiber reinforcement polymer (FRP) strips and end balls, was connected to the geosynthetic material and anchored into the soil. Test results showed that using GFR reinforcement significantly improved the uplift capacity of anchor plates. It was found that the inclusion of one layer of GFR, which rested directly on the top of the anchor plate, was more effective in enhancing the anchor capacity itself than other methods. It was found that by including GFR the uplift response was improved by 29%. Multi layers of GFR proved more effective in enhancing the uplift capacity than a single GFR reinforcement. This is due to the additional anchorage provided by the GFR at each level of reinforcement. In general, the results show that the uplift capacity of symmetrical anchor plates in loose and dense sand can be significantly increased by the inclusion of GFR. It was also observed that the inclusion of GFR reduced the requirement for a large L/D ratio to achieve the required uplift capacity. The laboratory and numerical analysis results are found to be in agreement in terms of breakout factor and failure mechanism pattern.
其他文献
7050铝合金软接触电磁连铸过程中的电磁场能促使熔体产生受迫流动,改善铸坯质量,抑制微裂纹。电磁场一方面通过均匀温度场降低内应力或应变,使金属高温脆性区主要处于受压状
研究了Mg-1.0Ca-0.3Zn合金在银离子剂量为1.5×1017cm-2注入条件下,在模拟体液(simulated body flmd,SBF)中的耐腐蚀性.通过纳米压痕和三电极体系法对合金的表面硬度和弹性模
采用镀Ti插入层在氢化物外延设备中制备了高质量自支撑GaN厚膜。X射线衍射测试发现(0002)峰摇摆曲线的半高宽为260arcsec;5K下样品带边发光峰的半高宽为3meV,室温下样品的带
在脆性的ZrCuNiAl块体合金中添加Nb,获得新型的Zr60.59Cu15.78Ni10.73Al10.75Nb2.15非晶合金。通过XRD、DSC及HRTEM对合金的结构及热力学参数进行测定,并采用静态压缩实验研
采用基于密度泛函理论的第一性原理平面波论调势方法计谋了Li-Si各种合金相的物理性质和电化学性能.结果表明:除了在反应过程中生成传统的固态电解持SEI膜之外形成的Li12Si7
系统研究了微量Ca的加入对Mg-12Zn-4Al-0.3Mn合金显微组织和高温抗蠕度性能的影响。结果表明,Mg-12Zn-4Al-0.3Mn铸造镁合金的显微组织主要由α-Mg基体和块状准晶晶界相组成,
采用表面机械研磨法(SMAT)对Zr-4合金进行处理,在其表面制备出纳米结构表层,并在不同温度下对其进行退火。利用偏光显微镜、X射线衍射仪、透射电镜、显微硬度计和电化学测量
形状记忆合金(SMAs)由于具有多种特殊性能,如伪弹性、形状记忆效应、生物相容性、高的比强度、高耐蚀性、高耐磨性、良好的抗疲劳性能,成为不断发展的先进材料。因此,形状记忆合
采用热分析、光学显微镜技术、扫描电镜技术、聚焦离子束和能量色散谱分析方法研究Ce对Al-Si-Cu合金中α(Al)-Al2Cu共晶形貌的影响。结果表明,在枝晶、硅和AlSiFeMn之间较小空
研究异种搅拌摩擦焊AA5083-H111和AA6351-T6铝合金的微观结构和力学性能。在3种不同的焊接速度(36、63、90 mm/min)下焊接AA5083-H111和AA6351-T6铝合金,分析焊接速度对接头力