【摘 要】
：
Chitosan (CS), hydrated zinc acetate, and rectorite (REC) were used as raw materials to prepare CS-embedded zinc oxide (ZnO) nanoparticle by a chemical precipitation process. Hydrogen-bonded REC-loaded ZnO-CS nanoparticle was to form ZnO-CS/REC nanocompos
【机 构】
：
College of Ocean and Bio-chemical Engineering, Fujian provincial Key Lab of Coastal Basin Environmen
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
Chitosan (CS), hydrated zinc acetate, and rectorite (REC) were used as raw materials to prepare CS-embedded zinc oxide (ZnO) nanoparticle by a chemical precipitation process. Hydrogen-bonded REC-loaded ZnO-CS nanoparticle was to form ZnO-CS/REC nanocomposite photocatalyst, its morphology and structure were analyzed by means of FTIR, XRD, TGA, SEM, and TEM. The effects of the catalyst dosage, methyl orange (MO) initial concentration and solution pH on photocatalytic performance were also discussed. The experimental results show that the ZnO-CS/REC nanocomposite has a particle size of 100 nm with good dispersion and uniformity. Under irradiation of visible light, 0.6 g/L photocatalyst was used to degrade MO in solution for 90 min at pH 6, then the MO solution (10 mg/L) was decolored by more than 99％, indicating that the ZnO-CS/REC nanocomposite exhibited highly photocatalytic degradation activity. Therefore, the photodegradation kinetic mechanism of MO in aqueous solution is presumed.
其他文献
To investigate the evolution of microstructure and wear behavior of TiSiN coatings with the variation of Si in targets and lays the foundation for its controllable mass production,Ti(1-x)SixN composite coatings were deposited onto Si (100) and cemented ca
Rice husk ash/natural rubber composites were fabricated by modifying rice husk ash with the rare earth coupling agent DN-8102. The structure of the rice husk ash and the morphological dispersion of the rice husk ash in a rubber matrix were charactered by
Fe-based coatings reinforced by spherical tungsten carbide were deposited on 304 stainless steel using plasma transferred arc (PTA) technology. The composition and phase microstructure of the coatings were evaluated using scanning electron microscopy (SEM
The thermal emittance of Cr film, as an IR reflector, was investigated for the use in SSAC. The Cr thin films with different thicknesses were deposited on silicon wafers, optical quartz and stainless steel substrates by cathodic arc ion plating technology
Long (15-40 μm),thin (diameter of 20 ± 5 nm),and well-dispersed CuNWs Cu nanowires were prepared.The high-resolution TEM and selected area electron diffraction showed that the CuNWs were single-crystalline.To investigate the growth mechanism,we examined t
Organically modified montmorillonite (OMMT) was incorporated into the complex of 18-crown-6 (CE) and polyimide-croum ether (PI[CE]), and its effect on the properties of the complex was evaluated in terms of thermal behaviors, coefficient of thermal expans
A combination of experimental measurements and numerical analysis was utilized to study the low-velocity impact damage of domestic carbon fiber-reinforced composites (CFRCs). The results indicated that the low-velocity impact damage induced pits and longi
A Fe modified Na2WO4 compound was synthesized by a solution impregnation method and was ball-milled with MgH2 to constitute a novel MgH2-Fe2O3/Na2WO4 composite. The effects of the Fe2O3/Na2WO4 additive on the hydrogen storage properties of MgH2 together w
Using lignite-based hypercoal as raw material, KOH as activator and CuO as microwave absorber, we prepared hypercoal-based activated carbons by microwave-assisted activation. The pore structure and the electrochemical performance of the activated carbons
The amorphous I/Au composite nanofilms were prepared by low vacuum direct current sputtering (LVDCS) method. The optimized preparation technologies contain growth pressure, time, gaseous environment and annealing conditions. The maximum fluorescence emiss