Novel si mulation method for fiber Bragg grating under inhomogeneous strainfields

来源 :Optoelectronics Letters | 被引量 : 0次 | 上传用户:jy168300124
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
The spectra of fiber Bragg grating (FBG) in inhomogeneous strain fields are distorted due to its inhomogeneity of both the periods and the effective refractive index. The couple mode theory and the Runge-Kutta method can be employed for exact simulation of the spectrum of Bragg grating in such field, but the convergence speed is slow. On the other hand, although the transfer matrix method could be used with higher convergence speed, the precision is poor because of the neglect of the grads of strain change. By improving the FBG equivalent period, a novel simulation method based on a modified transfer matrix method is proposed, which has the advantage of quick-convergence as well as good accuracy. The spectra of fiber Bragg grating (FBG) in inhomogeneous strain fields are distorted due to its inhomogeneity of both the periods and the effective refractive index. The couple mode theory and the Runge-Kutta method can be employed for exact simulation of the spectrum of Bragg grating in such field, but the convergence speed is slow. On the other hand, although the transfer matrix method could be used with higher convergence speed, the precision is poor because of the neglect of the grads of strain change. period, a novel simulation method based on a modified transfer matrix method is proposed, which has the advantage of quick-convergence as well as good accuracy.
其他文献
故事梗概好强任性的贝蕾,为了对初恋男友的一个承诺,有意考砸高考要赴澳留学。母亲高莉莉以为是自己在澳的前男友刘玮捣鬼,坚决反对。贝蕾说服父亲贝志强悄然出国。到悉尼后,
“等温变形”工艺在苏联和国外已获得广泛应用,它具有三个主要特点:1)冲模、工作区以及被加热的毛坯都有恒定的高温;2)钛合金的变形是在比较低的变形速度(0.1~2毫米/秒)下进
A broadband amplified spontaneous emission (ASE) source of 88 nm is demonstrated using novel bismuth-based erbium-doped fiber (EDF) with the length of only 49.2
A new type of high-power broadband superfluorescent source of Yb~(3+)-doped double-cladding photonic crystal fiber is reported experimentally, which is pumped a
我厂车间施工员忻明芳同志,大胆设想,在原有高频率超精加工设备上,取消了用磨条高频率振幅部分,运用珩磨齿轮的磨削工艺,创造性地运用氧化铝自浇磨轮——砂轮,代替磨条,革新
给定有限输入x和期望输出d,存在唯一的m+1长的最小平方滤波因子h~(m)=(h_0~(m),h_1~(m),…,h_m~(m)),为简单起见,记上式为q_m~2。一般q_m~2不趋于0(m→∞),只有当x为最小延迟
正弦尺用在车、铣、刨、磨工作中,能方便地校准、测量工件的角度。图1为正弦尺磁力表座的结构图,主要由磁力表座、正弦尺(L=100mm)、尺座等零件组成。表座制造时,需按图2技
11.紧固孔的加工精度 箱体零件上的紧固孔一般都是成组的,其轴线距偏差在0.15至0.25mm的范围内。螺纹按1级或2级精度加工。与螺孔同时加工的还有小直径的光孔。其中某些孔按
机床两导轨间的不平行度误差,是考核机床精度的重要指标之一;尤其是精密机床,导轨的几何精度要求很高,两导轨间的不平行度误差在0.005/1000~0.02/1000毫米之内。如何正确地反
一、概况该坝区内主要分布有轻微变质的前震旦纪板溪系石英岩、砂岩及板岩,岩层向上游右岸倾斜,倾角5-12°;岩性致密坚硬,可抗高压,但由于经受了多次的构造破坏,断层裂隙极