【摘 要】
：
A new technique is developed to measure the longitudinal thermal expansion coefficient of C/C composite material at high temperature. The measuring principle and components of the apparatus are described in detail. The calculation method is derived from t
【机 构】
：
DepartmentofAutomationMeasurementandControl,HarbinInstituteofTechnology,Harbin150001AerospaceResearc
【出 处】
：
ChineseOpticsLetters
论文部分内容阅读
A new technique is developed to measure the longitudinal thermal expansion coefficient of C/C composite material at high temperature. The measuring principle and components of the apparatus are described in detail. The calculation method is derived from the temperature dependence of the thermal expansion coefficient. The apparatus mainly consists of a high temperature environmental chamber, a power circuit of heating, two high-speed pyrometers, and a laser scanning system. A long solid specimen is resistively heated to a steady high-temperature state by a steady electrical current. The temperature profile of the specimen surface is not uniform because of the thermal conduction and radiation. The temperature profile and the total expansion are measured with a high-speed scanning pyrometer and a laser slit scanning measuring system, respectively. The thermal expansion coefficient in a wide temperature range (1000-3800 K) of the specimen can therefore be obtained. The perfect consistency between the present and previous results justifies the validity of this technique.
其他文献
Diode-pumped acousto-optic Q-switched pulse laser at 1.5–1.6 \mu m is obtained in an Er3 :Yb3 :LuAl3(BO3)4 crystal. Single-pulse laser operation with slope efficiency of 14% and threshold of approximately 100 mW is realized at an average absorbed pump po
地壳应变可根据水平方向的伸缩、倾斜、体积变化或重力变化等加以观察，这里采用对地壳水平面上的伸缩作连续观察。
为了探究不同激光扫描速度下NiCoCrAlY涂层的组织性能,通过激光熔覆技术在IN718表面熔化沉积了NiCoCrAlY涂层,分析涂层的成形情况、微观结构,并测试硬度、摩擦磨损性能,建立了扫描速度、微观结构和涂层性能之间的动态关系。实验发现,不同扫描速度下的NiCoCrAlY涂层成形良好,凝固组织为垂直于固液分界面、定向及“外延式”生长的柱状枝晶组织、等轴枝晶组织。随着扫描速度的增加,涂层温度梯度增大,凝固速率加快,晶粒组织细化,涂层显微硬度有小幅度增大;同时,涂层的平均摩擦系数和磨损率呈现先减小后增加的
Anisotropic dewetting polydimethylsiloxane (PDMS) surfaces, which consist of groove-like micro/nanostructures (so-called hierarchical structures), are fabricated using an ultrashort pulsed laser. The contact angles (CAs) are measured parallel to the micro
本文报导一种新型偏振无关光环行器的设计及实验结果。器件由偏振分离器、偏振组合器、法拉弟旋转器及半波片组成。对1.37微米不同偏振方向入射光,器件的插入损耗为2.8分贝,隔离为18～35分贝。
为了提高材料表面的耐磨性,实现材料的强韧结合,采用激光热流密度均匀分布的二维离散式5×5点阵光斑,对蠕墨铸铁材料的激光相变硬化过程进行数值模拟,通过改变激光功率和激光加载时间,分析了硬化过程中温度场和硬化层的变化。结果表明:基于光束离散的激光相变硬化温度场分布形态与点阵光斑的空间分布相对应,在激光加载结束时,每个小光斑中心点的温度同时达到峰值,整个光斑中心点的温度因各光斑温度场的叠加而达到最高,且沿着各光斑中心点的温度分布呈波浪形;在截面上随着深度增加,温度逐渐降低,材料的整体温度随着激光功率的增大和激光
提出了一种求解共焦镀层理想导体椭球粒子对任意角度入射高斯波束散射的解析方法。利用椭球矢量波函数把入射和散射电磁场展开，待求的展开系数由适当的边界条件推出的线性方程组确定。对于理想导体和镀层理想导体椭球粒子，给出了归一化微分散射截面的数值计算结果，并讨论了其散射特性。
我相信苏联人了解我们所有的秘密，甚至包括我们今后三十年的秘密。我们是对自己人保密，如在X射线激光器方面。现在有多混乱，因有关该计划的谎言可以发表,并已经发表。有关这些问题的真实情况，这些谎言的矛盾，我不能讲。我们中的混乱由保密造成。苏联人学到新东西是可能的，但可能性不大，因为他们至少比我先进。