祝《北京纺织》更上一层楼——纪念发行100期

来源 :北京纺织 | 被引量 : 0次 | 上传用户:zxing515
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
作为一名科技工作者,手头备有几种好的专业刊物是必要的.《北京纺织》是我爱读的纺织刊物之一.10多年来,她给我的启迪,给我的知识,无法用言语来表达、工作中有了空隙,总要翻翻《北京纺织》.1980年4月份从石家庄二棉调到扬州工作后,我仍然坚持阅读她.是她伴我工作,陪我思索,促使我在技术岗位上努力实践,奋力拼搏,促使我对生产过程中出现的各种现象进行抽象的科学的理论分析,进行由表及里、去粗取精的归纳思考,摸索其发生、发展的内在联系,进而取得了如何控制生产的理性认识.在这基础上我也时而写些文章投寄《北京纺织》,与同行们交流,向同行们请教.工程技术人员都有这样一种体会:一篇好的技术经验总结,每读之后,总会产生跃跃欲试的感觉,总想让别单位的好经验也能在本单位开花结果;一篇好的学术文章或理论探讨文章,每学之后,总会坐卧不安,总想抽时间接过该文想像的翅膀继续往更高处 As a science and technology worker, it is necessary to have several good professional publications on hand. “Beijing Textile” is one of the textile publications that I love to read. For more than 10 years she gave me inspiration and knowledge that I can not With words to express the gap in the work, always going to overthrow “Beijing Textile.” April 1980 transferred from Shijiazhuang two cotton Yangzhou work, I still insist on reading her is her work with me, with my pondering, Prompted me to work hard in the technical post, worked hard, prompting me to produce abstract scientific theoretical analysis of the various phenomena that occurred in the process of production, and to conduct the induction and reflection from the inside and the inside to the coarse and the fine, to explore the internal connection between its occurrence and development , And then made a rational understanding of how to control the production.On this basis, I also write some articles from time to time to post “Beijing Textile”, to communicate with colleagues, to ask their colleagues. Engineering and technical personnel have such an experience: an article Good technical experience summary, after each reading, there will always be eager to feel, always want to have good experience of other units can blossom in the unit results; a good scholarly article or theory to explore the article, after each study, always Sit down Ann, always want to take the time to take over the text of the wings of imagination to continue at higher
其他文献
我厂生产的3Z3.5—9.2/30型氧气压缩机气缸套(图1所示),最初采用传统的刚性结构夹具,外圆磨削后卸下夹具放置4小时后,实测圆柱度达0.17mm,严重影响了产品质量。对此,我厂进
西德DIN(国家工业标准)中有缩短钻头横刃的规定(如图1)。但是,该规定尚不充分,专家们仍注意研竟钻头刃磨方法对于孔加工精度等的影响,西德GUHRING公司最近针对钻头的刃磨方
对W18Cr4V轧后退火材,一次淬火(1285℃,4min油淬)断口上闪点缺陷,经宏观,微观断口观察;奥氏体晶粒测定;等温退火变形量、终变温度与轧后退火工艺以及使用寿命的验证试验,找出
高精度冲模大都采用滚珠导套。在导柱和导套之间配有滚珠套。每个套镶有滚珠96个。加工时需在滚珠套上钻孔,但需留120°锥度不完全穿透,然后放入滚珠,最后用镶珠杆将滚珠镶
在机械加工中常遇到偏心零件,下面介绍一种为C620车床设计的偏心卡盘座(附图)。用螺钉7和定位销6将半螺母4紧固在法兰座2上。滑动座1和法兰座2之间以半螺母4为导向键,可以自
刀具是金属切削加工的重要工具之一。它对发挥机床性能、提高生产率、保证加工质量、降低加工成本都有很大作用。特别是新型刀具的出现,常常把劳动生产率和加工质量提高到一
铸造镍基合金M38经过功率密度为2.3×10~4W/cm~2、连续CO_2激光束作用0.2秒处理后,形成了0.6毫米厚树枝胞状晶的表层;大量的TIC被固溶;γ’相及M23C6相重新以更细小的颗粒析
铝及其合金镀银的预处理一般采用浸锌酸盐法,其工艺较繁而且合格率低,故经济效益较差。我们采用镀锌预处理,方法简单、镀液稳定。只要严格按照工艺规程操作,合格率可达100%,
工频感应加热装置在热处理工艺上,目前多用于冷轧辊、柱塞及轮类等圆柱形大件的表面淬火,以及筒状和环状大型焊接件的局部热处理。对于“V”型或“O”型等孔型的型钢矫正圈
在机械零件的加工过程中,用同一样的设备,由于刀具的设计制造不一样,就会有不同的效率和精度。我厂加工 Y 200-Y280端盖是用自制的简易车床,采用特殊设计的通用组合刀排(见