【摘 要】
：
The interfacial oxygen transfer rate is one of the main factors to control the composition of alloys.The commonly employed method of studying the interfacial oxygen transfer rate is the chemical composition analysis;however,it is difficult to be studied i
【机 构】
：
School of Materials and Metallurgy,University of Science and Technology Liaoning,Anshan 114051,Liaon
论文部分内容阅读
The interfacial oxygen transfer rate is one of the main factors to control the composition of alloys.The commonly employed method of studying the interfacial oxygen transfer rate is the chemical composition analysis;however,it is difficult to be studied in situ.Here,a new method of measuring the oxygen transfer rate at the gas-slag and slag-metal interfaces was reported based on electrochemical analyses.The interfacial oxygen transfer rate in the smelting process of Inconel 718 superalloy was investigated at 1723,1773,1823,and 1873 K.The experimental results show that the electrochemical method can measure the real-time oxygen content;hence,this method is promising in controlling the oxygen content in alloys.As the temperature increased,both the equilibrium oxygen content and the rate of oxygen absorption increased significantly,and the increase was the most obvious when the temperature was 1873 K.The possible reason is that the increase in temperature weakens the mass transfer resistance of the electric double layer at the interface,thus accelerating the oxygen transfer rate.
其他文献
采用光学显微镜、小样电解、扫描电镜及能谱、ImageJ软件等分析检测方法,对SAE1144易切削钢由18 mm圆棒冷拉拔至15 mm八角棒过程中产生表面裂纹的区域进行研究.结果表明:八角棒裂纹扩展区有大颗粒状MnS夹杂、细长条形团簇状MnS夹杂以及大块的FeO夹杂,开裂面有大量密集的细长条状MnS;而大块的FeO夹杂是裂纹产生的微裂纹源,大颗粒状MnS夹杂、细长条形团簇状MnS夹杂是裂纹扩展的主要原因.
The interaction parameters of Nb in Fe-C-Nb melts at 1873 K were measured using the chemical equilibrium method.The Fe-C melts were equilibrated with the CaO-MgO-Al2O3-NbO2 slags under a controlled oxygen potential for 24 h.In addition to acting as the pr
The titanium industry can hardly bypass the titania-containing slags,and the slag physicochemical properties are essential in the metallurgical reactor design and process control.The TiO2-FeO-based slags and TiO2-SiO2-CaO-based slags are the main metallur
介绍了振动被引入金属凝固过程的发展历程,重点归纳了机械振动技术、振动激发形核技术、超声振动技术和脉冲磁致振荡技术运用于金属凝固过程控制的振动方式、应用领域、冶金效果及优缺点,总结了四种振动产生的方式和机理,概述了振动对金属液凝固的影响及具体形式,总结了现有振动改善凝固组织的机理和振动技术在金属凝固过程中的研究现状,最后对几种控制金属凝固的振动技术做了简要分析,并对其后续发展做了简单的展望,为以后研究振动技术在凝固过程中应用的学者提供一个参考.
Reducing the NOx emission from pelletizing process is of great importance to the green development of iron and steel industry.The flue gas temperature of preheating(PH)section during grate-kiln iron ore pelletizing process typically ranges within 850-1050
KR脱硫的渣资源化利用有利于促进钢铁企业的绿色化发展.KR脱硫渣中主要成分为CaO,且含有质量分数为1.0％～2.5％的硫,直接将K R脱硫渣回用于冶炼工艺会导致钢液增硫.若能将渣中的硫脱出,可有效促进KR脱硫渣在钢铁冶炼工艺的资源化利用.因此,针对当前KR脱硫渣综合利用存在的问题,总结分析有关CaS氧化过程的热力学和动力学研究现状,探究将KR脱硫渣中硫转化成为SO2的有利条件,分析将KR脱硫渣用于转炉造渣脱磷的可行性,以实现KR脱硫渣的冶金内循环利用.KR脱硫渣中的硫主要以CaS形式赋存在渣中,高温(温
The mathematical model of coupling fluid flow,heat transfer,solidification,solute transport,and the electromagnetic field of the bloom in the upper part of the strand was established with three nozzle types.Then,the flow field,distribution of the temperat
Multiple precipitating species in a 2.2 GPa grade precipitation-hardened martensitic stainless steel with balanced ductility were characterized at atomic scale by atom probe tomography.The results indicated that the clustering of solute atoms was promoted
Porous metals are a class of cellular materials with lightweight and unique mechanical,electrical,thermal,physical and acoustic characteristics.Magnesium and magnesium alloy foams have exhibited excellent advantages.In particular,open-cell Mg-based foams(
To investigate the transient transport and entrapment of argon bubbles and inclusions simultaneously during continuous casting,a 3D large eddy simulation model coupling molten steel flow,solidification and particle motion was constructed.In this model,mom